B7 15 mA fluid is pumped at a rate of 0.00156 m/s through a 0.025-m-diameter pipe to fill.awater tank as shown in Figure. What is the pressure drop between the inlet (section1) and the outlet (section 2) accounting for all losses?The density of the fluid is (1.00x10^3) kg/m and the dynamic viscosityis 1.12 x 10 -3 Ns/m2. The following are also known KL, elbow =1.5, KL, exit= 1 andsurface roughness, e =0.001 mm. Also take gravity, g = 10 m/s2.The elbows are enlarged for ease of visualisation and the lengths shown are those ofthe pipes.Answer should be in Pa with three significant figures. 15 m6 m6 m2Elbow6 m3 m111:34) ENG画2℃05-AprIA

Given Data The discharge is:Q=0.00156 m3/s The diameter of the pipe is:d=0.025 m The density of the…

A fluid is pumped at a rate of 0.00156 m/s through a 0.025-m-diameter pipe to fill.a water tank as shown in Figure. What is the pressure drop between the inlet (section 1) and the outlet (section 2) accounting for all losses?

A fluid is pumped at a rate of 0.00156 m/s through a 0.025-m-diameter pipe to fill.a water tank as shown in Figure. What is the pressure drop between the inlet (section 1) and the outlet (section 2) accounting for all losses?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 30-cm by 15-cm Venturi meter is mounted on a vertical pipe with the flow upward. One hundred twenty-six (126) liters per second of oil (s.g. = 0.80) flows through the pipe. The throat section is 15cm above the upstream section. If Cv=0.957, what is the difference in pressure between the inlet and the throat?
Show complete solution with diagram: A 3.81-cm diameter venturi meter is installed in a pipe with an internal diameter of 10.23 cm. A 127 cm manometer filled with mercury is used to measure the pressure difference across the venturi meter. If the manometer reads 101.6 cm when 15 °C water is flowing through the pipe, what is the flow rate of water (m3/min)? Assume that the venturi meter coefficient of discharge equals 0.98.
A pipe of 0.25 m diameter carries water at the rate of 7.2 m3/s.The pressure head at the entry of the venturimeter, used to measure the flow rate in the pipe, is equivalent to 6 m of water. If the pressure head at the throat is zero, calculate the throat diameter of the venturi.Include fbd.
A 100mm circular sharp edge hole in the end of a 150mm pipe discharges oil (s = 0.90). The vapor pressure in the closed tank is – 20 kPa, and the pressure head on the centerline of the pipe directly upstream from the orifice is 9m of oil. There is no submersion of the discharge. If CV = 0.97 and Q = 83 liters/s, find the discharge coefficient. Answer: C = 0.68
A 230-m-long pipeline delivers 20◦C water to a storage reservoir located downstream. The pipeline is galva-nized with an average roughness height of 0.2 mm. An axial pump is used to pressurize upstream water. Thewater surface in the reservoir is located 18 m above the centerline of the pump. The pump discharges waterat an absolute pressure of 400 kPa and a volume flow rate of 50 L/s. Calculate a diameter of pipe requiredto achieve such an operating condition. If needed, use the Moody diagram on the last page, or one can solvethe Colebrook equation using, for example, Matlab.
Two identical pumps are connected in series and deliver water through an 45cmdiameter, 2.2km long, commercial steel pipe from reservoir A (surface elevation = 50m) to reservoir B(surface elevation = 100m). Consider minor losses of a square-edged inlet, exit, and swing-type checkvalve. Determine the discharge, the total head added by the pumps, and the total power output. The pumpcharacteristics for a single pump is tabulated below. Assume that the kinematic viscosity is 1x10-6 m 2/s and a specific weight of 9.79kN/m 3 . Plot the system and pump characteristic curves on a single plot. Besure to label the axes appropriately (i.e., include units). Be sure to include a legend to demark the systemhead curve and the pump characteristic curve.
Water at 20°C is pumped through a smooth 12-cm-diameter pipe 10 kmlong, at a flow rate of 75 m3/h. The inlet is fed by a pump at an absolute pressure of 4 MPa.The exit is at standard atmospheric pressure (101 kPa) and is 200 m higher. Calculate the frictional head loss Hf and compare it to the velocity head of the flow.
Oil of viscosity 10E-3 Pa-s and specific gravity 0.90, flows through 60 m of 100mm diameter pipe and the pressure drop 13.8 kPa. What will be the pressure drop for a second oil of viscosity 30E-3 Pa.s and the specific gravity 0.95 flowing at the same rate through the pipe? Assume the pipe wall to be smooth.A. 19.4 kPaB. 98.7 kPaC. 142.2 kPaD. 192.5 kPa
Water flows through a 16-inch pipeline at 6.7 ft3/s. Calculate the Darcy friction factor using Colebrook-White Equation if the absolute pipe roughness, e, is 0.002 in. Then calculate the head loss due to friction in 1000 ft of pipe length. Use the water kinematic viscosity to be 1.2*10-5 ft2/s.
Oil flows at 55.9L/s in a pipe of 160mm diameter and 50m length. SG of oil is 0.9 and viscosity is 0.04 Pa-sec. If head loss is 5.22m, determine: a. Mean Velocity of flow (m/s) b. Type of flow c. Friction Factor d. Velocity at the centerline of pipe (m/s) e. The shear stress at the wall of the pipe (Pa)
Oil of density 950 kg/m³ and viscosity 1E-2 Pas is to be pumped 10 through a pipeline and the pressure drop must not exceed 2E5 Pa. What is the minimum diameter of pipe which will be suitable, if a flowrate of 50 tonne/h is to be maintained? Assume the pipe wall to be smooth. A. 0.025 mB. 0.175 mC. 0.855 mD. 0.008 m
A pipe 100mm bore carries oil of density 900 kg/m3 at a rate of 4 kg/s. thepipe reduces to 60mm bore and rises 120m. the pressure at this point isatmospheric (zero gauge) assume no frictional losses.Determine:The volume per secondThe velocity at each sectionThe pressure at the lower end The above pipe is exchanged for a parallel pipe with a cross sectional area of 0.3m2 and is 20 m long, with a surface roughness coefficient of 0.005. The dynamicviscosity of the water is 1.002 x 10-3 Ns/m. Find the Reynold’s number of the flowand use Haarland’s formula to find the friction coefficient and Darcy’s formula todetermine the frictional pressure loss. Then determine the pressure at the outlet ofthe pipe.What does the magnitude of the Reynolds number mean to fluid flow