diameter solid steel cylinder in which a 7 mm diameter hole has been drilled from end B up to point C. The shaft is attached to fixed supports at each end, and a 150 Nm torque is applied at C. The torque reaction at A is 72 Nm. What is the max shear stress in the shaft? Input your answer as a value only in MPa to one decimal place without +/- sign. A 150 Nm L₂

diameter solid steel cylinder in which a 7 mm diameter hole has been drilled from end B up to point C. The shaft is attached to fixed supports at each end, and a 150 Nm torque is applied at C. The torque reaction at A is 72 Nm. What is the max shear stress in the shaft? Input your answer as a value only in MPa to one decimal place without +/- sign. A 150 Nm L₂

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.8.3P: A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A...

See similar textbooks

Similar questions

A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
If the shaft is made of red brass C83400 copper with an allowable shear stress of ?allow = 20 MPa, determine the maximum allowable torques T1 and T2 that can be applied on A and B. Also, find the corresponding angle of twist of end A. Set L = 0.75 m "Mechanics of Materials, Hibbeler"
The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the torques 2T and 3T at points A and B, respectively. If tallow = 35 MPa and (fA/C)allow =2o, determine the maximum permissible value of the torque T. Use the table given below and your student ID to find the values of L1, L2, and D. Student ID L1 (m) L2 (m) D (mm) 1131731 1 0.6 78
The mean dimensions of the cross-section of the leading edge and torsion box of an airplane wing can be approximated as shown. If the wing is made of 2014-T6 (G = 19 GPa) aluminum alloy having an allowable shear stress of Tallow = 158 MPa, and the wall thickness is 12 mm. Determine the maximum allowable torque and the corresponding angle of twist per meter length of the wing.
Two sections of steel drill pipe, joined by boltedflange plates at B, are being tested to assess the adequacyof both the pipes. In the test, the pipe structureis fixed at A, a concentrated torque of 500 kN ? m isapplied at x = 0.5 m, and uniformly distributed torqueintensity t0 = 250 kN . m/m is applied on pipe BC.Both pipes have the same inner diameter d = 200 mm.Pipe AB has thickness tAB =15 mm, while pipe BChas thickness tBC =12 mm. Find the maximum shearstress and maximum twist of the pipe and their locationsalong the pipe. Assume G = 75 GPa.
The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque T (in Nm) that can be applied to the ends of the shaft without exceeding a shear stress of 70034763 Pa and angle of twist of 2.23ᴼ. Use G = 83000000000 Pafor the shaft, x = 2.3 m, and y = 1.89 m. Round off the final answer to two decimal places.Please help me, I only have 30 mins left. TY!
PLEASE ANSWER ASAP TY! The shaft shown has a diameter of 30 mm and is fixed at points A and B. Shear Modulus = 75 GPa. a) What is the internal torque in segment AC (in N-m)? b) Determine the maximum torsional shear stress experienced at segment AC (in MPa). c) What is the torsional shear stress at the center of the cross-section of the shaft (in MPa)? d) Determine the reactive torque at point B (in N-m).
A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an outside diameter of 0.51 in. and an allowable shear stress of 4500 psi. Segment (2) is a solid aluminum shaft with an outside diameter of 0.41 in. and an allowable shear stress of 6000 psi. Determine the magnitude of the largest torque TC that may be applied at C. Express your answer in lb-in rounded to the nearest tenths.
A hollow steel shaft is stressed to 55 MPa by a torque of 135600Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter and G = 83 GPa.