A hollow steel shaft is stressed to 55 MPa by a torque of 135600Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter and G = 83 GPa
Q: Power transmitted by a hollow shaft at 300 rpm is 800 kW. The ratio of outer diameter to the inner…
A: Given data:- power=800Kw N=300rpm dodi=1.5 Tmax=1.4 Tmean τper=80 MPa…
Q: What is the minimum diameter of a solid steel shaft that will not twist through more than 6° in a…
A:
Q: A 2-in diameter steel shaft rotates at 150 rpm. If the shearing stress is limited to 10 ksi,…
A:
Q: Hollow and solid shafts have the same material, length and the same outer radius as shown. The inner…
A:
Q: solid shaft is transmitting 9 KW at 550 r.p.m. Determine the diameter of the shaft if the maximum…
A: for solution refer below images.
Q: The torque transmitted by a solid shaft of diameter 10 mm and shear stress 75 MPa Select one: a.…
A: Given data: Diameter of the solid shaft, D= 10mm Shear stress, s=75MPa=75N/mm2
Q: A solid 38 mm diameter shaft is rotating at a speed of 510 rpm with a maximum shear stress of 78…
A:
Q: a solid shaft in a rolling mill transmits 20 kw at 2r/s. determine the diameter of the shaft if the…
A:
Q: A solid circular shaft is required to transmit 200 kW while turning at 90 rpm (rev/min). The…
A: Consider a shaft having diameter 'D' is subjected to a twisting moment 'T'. Then, from torsion…
Q: hollow shaft with outside diameter of 14 cm and a wall thickness of 0.80 cm transmits 200KW at 400…
A: Given Data Do=14 cm t=0.8 cm P=200 kW N=400 rpm L=5 m
Q: A solid shaft in a rolling mill transmits 30kW at 100 rpm. Find the diameter in mm of the shaft so…
A: Answer: The diameter of the shaft is 63.35 mm. Hence, the correct answer is option (c).
Q: 2. The composite shaft of total length 1.8 m consists of 5 mm thick brass and is fixed to a 30 mm…
A:
Q: A solid shaft transmits 1.7 kW of power at 4.4 Hz. What is the smallest safe diameter of the shaft…
A: The expression to calculate the maximum shear stress is…
Q: circular solid shaft made of vibranium has G=80 Mpa and has a limiting torsional shear stress of 60…
A:
Q: Figure Q6 shows a circular shaft AB and a square shaft BC where it is fixed at C. а. Determine the…
A:
Q: A shaft when subjected to pure torsion developed a stress of 50 Mpa. If polar moment of inertia is…
A:
Q: A hollow steel shaft with an outside diameter of 80 mm and a wall thickness of 11 mm is subjected to…
A:
Q: A solid steel post is subjected to pure torsion. Given: -post Diameter = 65 mm -length = 2.75 m…
A:
Q: A hollow steel shaft with an outside diameter of 90 mm and a wall thickness of 10 mm is subjected to…
A:
Q: Q) A two-segment shaft is used to transmit power at constant speed through the pulleys shown above…
A:
Q: A solid circular steel shaft having an outside diameter of D = 1.25 in. is subjected to a pure…
A:
Q: A tubular steel [G = 79 GPa] shaft with an outside diameter of D = 89 mm and a wall thickness of t =…
A: Given Data The modulus of rigidity is: G=80 GPa The outside diameter is: D=89 mm The thickness of…
Q: Q.4) A composite shaft is subjected to two torques as shown below. Shaft ABC is a hollow…
A:
Q: Find the maximum stress developed in a stepped shaft when it is subjected to a: i) Torque of “T” Nm.…
A:
Q: shaft with a diameter of 50 mm and a length of 1300 mm with a safe shear yield strength of 20 N /…
A: Given:d=50 mml=130 mmSys=20 MPaT=565 NmG=80 GPa
Q: Problem1: The entire composite shaft shown in the following figure is manufactured using steel with…
A: GivenG=80GPatorque =Tτa=75MPa
Q: A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum…
A: Given:Length of the hollow shaft, L=1 mPower transmit, P=30 kWSpeed of the shaft, N=700 rpm,Angle of…
Q: A shaft with a hollow cross section is subjected to torque of magnitude T = 5.5 kN-m. If the outer…
A:
Q: Calculate the maximum and minimum shear stress in a hollow circular shaft of outer diameter 20 mm…
A: Given data T=92.7 N-mD=20 mmt=2 mmd=16 mm
Q: A compound bar consists of a steel and bronze segment (Gs t= 80 GPa and Gbr = 40 GPa), The limiting…
A:
Q: steel shaft 8 ft long that has a diameter of 3 inches is subjected to a torque of 27 kip ft.…
A:
Q: Determine the power in kilowatts transmitted by the solid shaft if the radius is 7.5mm and it…
A:
Q: Problem 3
A: Sign Convention: Consider anticlockwise torque as positive and clockwise torque as negative.Refer to…
Q: 4) Shafts with lengths 5m and4 m are connected by gears. The diameter and shear modulus for both…
A: Given, Shaft lengths , 4m and 5m. Diameter of the shafts , d= 10cm Shear modulus of the shaft ,…
Q: A hollow steel [G = 12,000 ksi] shaft with an outside diameter of 3.50 in. will be subjected to a…
A:
Q: Maximum shear stress developed on the surface of a solid circular shaft under pure torsion is 235…
A:
Q: 3) Two circular shafts (shown in Figure) made of the same material and have the same length are…
A:
Q: Design a hallow shaft (Diameter and length) that develops 80 kW of power while rotating at a speed…
A:
Q: Determine the diameter of a solid steel shaft which will transmit 112.5 kW at 200 rpm. Also…
A: Given data, P= 112.5 kW =112500 W N= 200 rpm. θ=1.5° =0.0261799 rad. τ=55 N/mm² =55000000 N/m²…
Q: A steel shaft with a diameter 45 mm and length 1.30 m transmits 55.50 kW from an electric motor to a…
A: Given data Diameter of shaft = d= 45 mm = 0.045 mLength of shaft =l = 1.30 mPower Delivered =P =…
Q: A hollow steel shaft with an outside diameter of 76 mm and a wall thickness of 5 mm is subjected to…
A:
Q: The shaft consisting of steel and aluminum segments carries the torques T and 3T. Find the largest…
A:
Q: A solid circular steel shaft having an outside diameter of D = 1.00 in. is subjected to a pure…
A:
Q: A solid steel shaft 4.5 m long is stressed at 75 MPa when twisted through 4.5°. What power can be…
A: Given: Twisting angle, θ = 4.5° = 4.5°π180° Stress, τmax = 75 MPa Length, L = 4.5 m = 4500 mm G =…
Q: A circular shaft measuring 3 meters in length with an inner and outer radius of 30 mm and 60 mm…
A: Given data: Length of shaft, L =3 m Inner radius, r1=30 mm = 0.03 m Inner Diameter = 0.06 m Outer…
Q: A solid circular steel shaft having an outside diameter of 1.50 in. is subjected to a pure torque of…
A: Answer: The correct answer is option (b) i.e. 12.57 ksi.
Q: 3) Two circular shafts (shown in Figure) made of the same material and have the same length are…
A:
Q: The compound shaft, consisting of steel and aluminium segments, carries the two torques shown in the…
A:
Q: 3) Two circular shafts (shown in Figure) made of the same material and have the same length are…
A:
Q: A compound shaft consisting of a steel segment and an aluminum segment is acted upon by two torques…
A: GIVEN DATA - SHEAR STRESS IN STEEL SHAFT =82MPa SHEAR STRESS IN STEEL SHAFT =82MPa ANGLE OF TWIST…
Q: A hollow nickel-steel shaft, whose outside diameter is twice the inside diameter, is to transmit…
A:
A hollow steel shaft is stressed to 55 MPa by a torque of 135600Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter and G = 83 GPa.
Step by step
Solved in 2 steps
- A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
- The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
- A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
- A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi.