As shown in figure, a homogeneous 50-kg rigid block is suspended by the three springs whose lower ends were originally at the same level. Each steel spring has 24 turns of 10-mm-diameter on a mean diameter of 100 mm, and G = 83 GPa. The bronze spring has 48 turns of 20-mm-diameter wire on a mean diameter of 150 mm, and G=42 GPa. Compute the maximum shearing stress in each spring using approximate equation.

As shown in figure, a homogeneous 50-kg rigid block is suspended by the three springs whose lower ends were originally at the same level. Each steel spring has 24 turns of 10-mm-diameter on a mean diameter of 100 mm, and G = 83 GPa. The bronze spring has 48 turns of 20-mm-diameter wire on a mean diameter of 150 mm, and G=42 GPa. Compute the maximum shearing stress in each spring using approximate equation.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
THE ANSWER MUST BE IN FOUR DECIMAL PLACES the steef shaft shown in figure rotates at 4Hz with 35 KW taken off at A, 20 kW removed at B and 55 kW applied at C. Using G=83 GPa, find the maximum shearing stress and the angle of rotation of gear A relative to gear C
The following beam is supported by an aluminum bar at C, a steel bar at B, and a brass bar at D. The distance b is equal to 50 mm. The data is shown in the table:If the maximum rotation that can occur at point A is 0.25 radians clockwise, determine: a. The maximum force P that can be applied. Answ: 28347.97 kNb. The normal stress in the aluminum, steel, and brass bars. Answ: 25 000 MPa, 17500 MPa, 25937.5 MPa
3.Figure (a) shows a rigid bar that is supported bya pin at A and two rods, one made of steel and theother of bronze. Neglecting the weight of the bar,compute the stress in each rod caused by the 50-kN load, the following data：
The pipe AB shown in the figure has an inner diameter of d = 86 mm and an outer diameter of D = 110 mm. Assume its end is tightened against the support at A using a torque wrench at B. [P = 100 N, D = 110 mm, d = 86 mm, b = 280 mm, a = 360 mm] Find the torque created by the force P. Find the second polar moment of area (J) for the cross-section of the pipe. Find the stress at the outer wall. Find the stress at the inner wall.
Proposed exercise N ° 01 Find the angle of torsion of the free end with respect to the fixed end of the system in the figure. The material is steel and the dimensions are in cm. Proposed exercise N ° 2 Find the length that a hollow steel bar of D = 1.5cm and d = 0.5cm in diameters must have for its ends to rotate 30 ° relative to each other. An allowable shear stress of 713.8 kg / cm2 must not be exceeded, and G = 8.1573x105 kg / cm2
A solid rectangular object having dimensions of l = 4.00 cm, w = 3.00 cm, and h = 1.00 cm is subjected to a compressive stress having a force of F = 2.00×10⁵ N applied perpendicularly on the right and left faces of the rectangular object. This stress causes compression on the box by Δl = 1.25% of its length as shown in Figure A. The Shear modulus of the rectangular object is just 35% of its Young's modulus. If this force was instead applied on the upper and lower faces on the rectangular object without changing the direction of the force (Figure B), by how much distance would the upper face be deformed with respect to the lower face of the rectangular object?
Calculate the maximum shear stress tmax the maximum bending stress emax in a wood beam (see figure) carrying a uniform load of 22.5 kN/m (which includes the weight of the beam) if the length is 1.95 m and the cross-section is rectangular with a width of 150 mm and height 300 mm, and the beam is either (a) simply supported as in the figure part a, the or b has sliding support at right as in the figure part b.
length=7m height=250mm UDL on the beam=38.5KN/M d=812mm Mass of the beam=65.9kg/m a. Consider design loads( udl+self weight) b. Calculate and draw the Bending Moment Diagram (BDM).What is the value of the maximum bending moment? c. Calculate and draw the Shear Force Diagram (SFD).What is the value of the maximum shear force? d. Using the table, calculate the maximumdeflection of the beam.
From the given figure below and its properties, calculate the stress at the top where the maximum moment is located. (MPa) Properties: Beam width = 207 mmBeam height = 386 mmWLL = 12.48 kN/mWDL = 15.26 kN/mSpan of the beam = 8 mPrestressing force = 293 kNeccentricity = 135 mm
Consider a wood beam (see figure) carrying a uniform load of 16.5 kN/m (which includes the weight of the beam). The length is 1.55 m and the cross section is rectangular with width 150 mm and height 300 mm. * Inserted Photo* If the beam is simply supported as in figure part (a), calculate the maximum shear stress ?max and the maximum bending stress ?max. (Enter the magnitudes in MPa.) ?max= ? MPa ?max= ? MPa (b) If the beam has a sliding support at right as in the figure part (b), calculate the maximum shear stress ?max and the maximum bending stress ?max. (Enter the magnitudes in MPa.) ?max= ?MPa ?max= ? MPa