differentiate between shaper and planer machine any six difference

Q: It is a widely use tool for laying out squaring and checking work.It consists is a square head and a…

A: following is the answer to the above question-

Q: machine elements question about shafts

A:

Q: 2. Draw the sketch of 'Drilling machine' and explain any four parts. Use pencil to draw the neat…

A:

Q: 3. Differentiate between Caption and Turret lathe.

A: LATH MACHINE  A tool that spins a component around a rotating axis to do several tasks including…

Q: bite angle in degree will be

A: Given; Thickness of a metallic sheet is reduced from an initial value to a final value in one single…

Q: what is the measured distance to the nearest eigthth between the outside corners of the tongue and…

A: FRAMING SQUARE  A framing square, also known as a steel or carpenter square, can be the most…

Q: The angle of forst of c

A: Given; From given figure: A stepped shaft subjected to a twisting moment applied at BShear modulus…

Q: Explain any five safety precautions to be followed while working on lathe machine.

A: Lathes are workshop tools used for performing tasks such as cutting, knurling ,drilling etc. The…

Q: b) With a neat sketch differentiate between boring and tapping operation.

A: This question is from manufacturing engineering.  We have to define boring and tapping operation.

Q: Give one problem solving question about "Method of Sections" and show the solution

A:

Q: A facing operation is normally .18 performed on which one of the following ? machine tools: , , or

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: What part of an engine or Turret lathe slides move in the direction normal to the beds Ways

A: Given:- Turret lathe To find:- The part that moves in the direction normal to the bed of the bed

Q: Lathe Machine tool is an example of three axes machines

A: Lathes, by definition, are 2-axis machines. Once machines advanced to incorporate 3-axis, 4-axis…

Q: c) Write short notes on the principle of up milling with a neat sketch.

A: Up milling is a type of milling in which peripheral cutters are used.

Q: Describe thrust angle.

A: Introduction  The thrust angle is basically used as a major angle for alignment of the rear and…

Q: milling machine operational parts

A: Milling machine: It has a rotating cutting tool having number of cutting edges which is used to…

Q: Clapper box is found in following machine tool. O a. Lathe machine O b. Drilling machine С. Shaper O…

A: Clapper box is a hinged device that allows a reciprocating cutting tool to clear the job on the…

Q: Dad with an angle of 10° and radius

A:

Q: о ре cional area

A:

Q: Tool wear refers to abrasion on .............. and the tool edge become worn a) Cutting edge. b)…

A: Tool wear refers to abrasion on .............. and the tool edge become worn a) Cutting edge. b)…

Q: (a) Differentiate with sketches (with parts marked) between the jib and bridge crane..

A: A jib crane has one point of contact from which the crane expands. A gantry crane in any case is…

Q: What type of simple machine is a wheelbarrow? lever inclined plane O wedge screw

A: A machine used to reduce the effort while performing a task is called a simple machine.

Q: Explain about corrective maintenance of a machine tool.

A:

Q: Describe about straddle milling operation

A: Explanation :-  Straddle milling - when two sides milling cutters are used to machine two opposite…

Q: Machine Elements.

A:

Q: differentiate between caption and turret lathe

A: Capstan and Turret lathe is one of the broad classifications of a Lathe

Q: On increasing the value of rake angle, the strength of tooi.

A: Rake angle is defined as the angle between the normal line to the workpiece and the edge of the…

Q: Sketch shaper machine and explane its parts?

A: Parts of a shaper function are, Base: The Base is fixed to the shop floor and built to take the…

Q: The tool used for marking center is __________. a.   Steel rule   b.   Divider   c.…

A: Solution:

Q: The width of the cutter must be .. to the workpiece width in the slot milling

A: Answer is Less

Q: Differentiate between Shaper and Planer Machine?

A: Shaper Machine                     Planer Machine Stroke length in the shaper…

Q: Drilling operation to produce conical shape on a drilled hole is known as a. Boring b. Counter…

A:

Q: what maximum angle can the ramp make with the horizontal before the block starts to slip down?

A:

Q: Can someone show me how to do the roller, pin, and built-in supports( 2 each) and point them.

A:

Q: What kind of machine tool is shown in this figure? Speed moti Planer machine Broaching machine…

A:

Q: In shaper machine the workpiece will be _during machining Select one: a. Stationary b. Reciprocating…

A:

Q: The time taken to drill a hole

A: Given; Feed rate of a drill is;   f= 0.25 mm/revAt a rotating speed at, N= 300 rpmWhere, Plate…

Q: Milling Machine tool is an example of two axes machines

A: Milling cutting tool is the is an example of two axes machines. Answer: True

Q: Type of milling operation to produce flat surfaces with cutter axis perpendicular to the milled…

A: according to the given details in the question.

Q: 3. With neat sketches write short notes on any two different work holding devices use on a planer…

A: Angle plates An angle plates is an L-shaped piece of cast iron and steel accurately machined to an…

Q: Safety goggles are required when working on lathe machine. Select one: True False

A: Lathe machine is one of the oldest machine used in manufacturing field. Due to its It's versatile…

Q: of drill

A:

Q: machining time per pass

A: Given data; Depth of cut,b=2 mmTable feed rate,f=18 mm/minBlock length,l=200 mmMilling cutter…

Q: equal par machine is

A:

Q: "N" JOBS- “3" MACHINE

A: Where Machine G is - A+B=8+5=13 10+6=16 6+2=8 7+3=10 11+4=15 And Where H - B+C 5+4=9 . .

Q: Type of milling operation to produce flat surfaces with cutter axis perpendicular to the milled…

A: True  Explanation :-  In face milling , milling cutter is placed  is placed perpendicular to the…

Q: ifferentiate 3 types of lathe machine in terms o

A: Lathe machine: Lathe machine has a chuck and the toolpost, Chuck is used to holding the workpiece…

Q: 4. Differentiate a lathe machine into a shaper machine in terms of operating principle

A: GIVEN DATA - LATHE AND SHAPER MACHINE GIVEN WE HAVE TO DIFFERENTIATE IN TERMS OF OPERATION

Q: process used for cutting a gear on a milling machine is called The a. Gear forming b. Gear shaping…

A: Option c is correct