What type of simple machine is a wheelbarrow? lever inclined plane O wedge screw

Q: Carriage is mounted on the outer guide ways of lathe bed and it can move in a direction parallel to…

A:

Q: Applying finger pressure on the belt near the pulley end is the correct method to check the tension…

A: True

Q: PROVIDE DIFFERENT ACCESSORIES IN SHAPER MACHINE WORKS VERTICAL AND HORIZONTAL WITH PICTURE

A: Shaper machine is a cutting machine that converts reciprocating motion of a flywheel into linear…

Q: It is a widely use tool for laying out squaring and checking work.It consists is a square head and a…

A: following is the answer to the above question-

Q: Construct all extension lines, dimension lines, leaders, and arrowheads that are necessary to fully…

A: Leader line: I have mentioned the name on leader lines in the figure. Basically, the leaders lines…

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is O…

A: The correct maintenance procedure for gib adjustment on the lathe machine Adjust the gib to new…

Q: the omnidrive that was mentioned above should be an agriculture related machine

A: Omni drive is an agriculture-related machine that is used to help the farmers in their fields.…

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: what is the impact of mechanical vibration on following a. Bearing House of Lathe machine b.…

A: Answer         c. Fatigue life of materials

Q: the largest internal normal force in

A: To find largest internal normal force in  the bar

Q: what is the measured distance to the nearest eigthth between the outside corners of the tongue and…

A: FRAMING SQUARE  A framing square, also known as a steel or carpenter square, can be the most…

Q: 2. It is used to loosen or tighten screws that have a star-like depression on the top, a feature…

A: Since you have posted a multiple independent questions in a single question. We will solve the first…

Q: To fix a machine on the ground, we can use Select one: O a. Splines and Colts O b. Studs & Thread…

A: Splines and Colts, Keys and keyways are used to connect gears/shafts Bolts and nuts are used to…

Q: Q3: (a) describe the location and function of the following: i. Gudgeon pin ii. Rod shank ii.Large…

A:

Q: and the restorer

A:

Q: The copper head hammer is used for releasing hold pin in the chuck.

A: Yes, It is True. The copper head hammer is used for releasing hold pin the chuck.

Q: The following device is used to hold a workpiece securely during drilling in Drilling machine Select…

A: It is required determine which of following device is used to hold a workpiece during drilling…

Q: Identify the type of milling operation in which the cutter axis is perpendicular to the workpiece…

A: In the Face milling process, the cutter axis is perpendicular to the workpiece being machined.

Q: The depth measurement is done by ___________________part of a Vernier Caliper. Ratchet Anvil Spindle…

A:

Q: Which of the following works by dragging a bucket towards the machine? Dragline Clamshell O Loader…

A: It is required to determine which machine works by dragging a bucket

Q: Chip guard has to be installed between the point of operation and the operator, is a safety…

A:

Q: A bridge crane is a material handling equipment that can lift load and unload which can rotate in a…

A:

Q: Clapper box is found in following machine tool. O a. Lathe machine O b. Drilling machine С. Shaper O…

A: Clapper box is a hinged device that allows a reciprocating cutting tool to clear the job on the…

Q: Describe about straddle milling operation

A: Explanation :-  Straddle milling - when two sides milling cutters are used to machine two opposite…

Q: ion 3 plain the importance of: rake angle relief angle nose radius

A:

Q: Which among the following part which is not belonging to a milling machine. a. Compound slide b.…

A: Main parts of the milling machine: Column and base Knee Saddle and swivel table Worktable Power…

Q: The centrifugal force resulting from shaft rotation is proportional to: The square of the angular…

A: Given The centrifugal force resulting from shaft rotation is proportional to: To choose options :…

Q: On increasing the value of rake angle, the strength of tooi.

A: Rake angle is defined as the angle between the normal line to the workpiece and the edge of the…

Q: What are the parts of Milling Machine  (Make sure the parts are labeled accordingly)

A:

Q: What is the point at which a machine has a tendency to grab a body part? a. Grip point  b. Point…

A: Solution:   The correct option with necessary explanation is given below:

Q: The tool used for marking center is __________. a.   Steel rule   b.   Divider   c.…

A: Solution:

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is On…

A: The engine lathe is a high-precision machine tool that needs to be treated with care. The lathe's…

Q: nance pr Tollowed wniie performing gib adjustment on a lathe machine is O On the front face of the…

A:

Q: Can someone show me how to do the roller, pin, and built-in supports( 2 each) and point them.

A:

Q: .Q21 The forces do not cause rotation

A: The concurrent forces traverse through a similar point. It means that other forces balance each…

Q: briefly discuss the components of arbor press machine.  thanks

A:

Q: What kind of machine tool is shown in this figure? Speed moti Planer machine Broaching machine…

A:

Q: _1. What is a type of tool that used to loosen or tighten screws that have a star-like depression on…

A: As per bartleby guidelines we are allowed to solve only 1st  3 subparts if multiple subparts are…

Q: The shorter the __ is, the more force the lever will apply. A. Fulcrum  B. Acceleration  C. Load…

A: The heavy load can be handled with small effort through mechanical advantage of a mechanism. In…

Q: Helical gear

A: Ans is Helical gear

Q: platform weighing machine

A: From very early times, civilizations used weighing machines in business transactions. Over the…

Q: The question and problem are fully listed in the attached image. I really care more about the…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: In uptight drill machine, the power is transmitted from electric motor to spindle with help of belt…

A: Drilling machine is a mechanical equipment used to introduce holes into a specimen which are in…

Q: Which manufacturing machine is used for cylindrical symmetric parts? OA Drilling Machine D Laser…

A: CNC turning machine (Lathe) is used to produce the components that are symmetrical about the axis.…

Q: If a washer has a 1” outside diameter and a .50” inside diameter, what is the distance between the…

A: Given data, D= 1 in.  d= 0.50 in.

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is The…

A: Given: The wrong maintenance procedure followed while performing gib adjustment on a lathe machineis

Q: A machine that includes a rotating wheel sits on a workbench. The wheel has a diameter of 14 inches…

A: Given that, Diameter of the wheel, D=14 inches,Height of wheel from the surface of workbench, H=15…

Q: The copper head hammer is used for releasing hold pin in the chuck. Select one: True False

A: The copper hear hammer is a hammer in which striking portion of the hammer (or head) are…