Difficult Problem: If magnitude of MA is 1200 kN – m and the distance between A and B is 3 m, what is the force FB and distance d so that the system shown at the right is equivalent to a force-couple system acting at point D, where the horizontal component of this force is R, = 112 kN to the right and the corresponding couple is 635 counterclockwise.

Difficult Problem: If magnitude of MA is 1200 kN – m and the distance between A and B is 3 m, what is the force FB and distance d so that the system shown at the right is equivalent to a force-couple system acting at point D, where the horizontal component of this force is R, = 112 kN to the right and the corresponding couple is 635 counterclockwise.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter2: Basic Operations With Force Systems

Section: Chapter Questions

Problem 2.79P: The arm ABCD of the industrial robot lies in a vertical plane that is inclined at 40 to the...

See similar textbooks

Similar questions

The 1800lbin. couple is applied to member DEF of the pin-connected frame. Find the internal force systems acting on sections 1 and 2.
Find the internal force systems acting on sections 1 and 2.
The arm ABCD of the industrial robot lies in a vertical plane that is inclined at 40 to the yz-plane. The arm CD makes an angle of 30 with the vertical. A socket wrench attached at point D applies a 52-lb ft couple about the arm CD, directed as shown. (a) Find the couple-vector that represents the given couple. (b) Determine the moment of the couple about the z-axis.
Two equivalent force-couple systems are shown below. If M1 and M2 are 300 and 20 lb-ft, respectively, calculate forces S and Q (both in lb) and the dimension d (in ft). Note that the sense of S and Q are assumed only. Also, the magnitudes of forces P1=53.98N and P2=580.2N
The figure below shows three forces of 20 lb each applied to a rectangular block1. Reduce the three forces to a single force and a single couple at the origin O2. Can the system be reduced to a single force? Please explain your answer3. Can the system be reduced to a single couple? Please explain your answer
Given a 2-D force system with geometry as shown. Find the magnitude of the equivalent couple moment (Nm) acting at O if P = 509 N , Q = 388 N, and T = 444 N . Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of moment: use CW if clockwise , CCW if counterclockwise.
SITUATION 5: The hook shown in the Fig. SRB-004 is subjected to three forces A, B, and C. If A = 8 kN, B = 5 kN and angle α = 32°. Calculate the value of angle θ (degrees) if the resultant of the three forces is 7.5 kN along the y-axis. (Answer: 37.32) If the resultant of the three forces A, B, and C is 14.5 kN, and θ = 83°, what is the value of C, in kN? (Answer: 6.64) If C = 6 kN, and θ = 45°, how much is the resultant pulling force in the eyebolt, in kN? (Answer: 9.49)
The resultant couple moment for all the forces shown in the figure below is?
The rigid body shown below (Fig 1) is subjected to four cable forces applied at different points A, B, and C.(a) Determine an equivalent system consisting of a Force-Couple system at point O. (b) Determine an equivalent force system consisting of a Single Force and specify the y-coordinate of the point where its line of action intersects the y-axis.
If P= 20 lb in the figure, replace the three couples with a single equivalent couple, specifying its magnitude and the direction of its axis.
The hydraulic cylinder shown in the figure exerts a force of 3 kN directed to the right at point B and to the left at point E. Determine the magnitude of the couple M required to rotate the drum at constant speed clockwise. The picture is attached
Force P and couple M are applied at A as shown. 1. Suppose an equivalent system was made such that only force at B and a couple are present. What gives the magnitude of force at B and the couple in the equivalent system? 2. If the force P and couple M is to be replaced with a single force, where is the point of application of this single force along bar ABCD in order to have the same external effect as the original set of force P and couple M? (How many m to the left or right of B)