For the force of system shown in the figure below, determine the resultant and locate with respect to point A. Requires RespoBhupinder Singh: Attempt 1e Left:0:44:08Show ALL your work and round your answer to 1 decimal p400 lb30250 lb4 ft40°4 ft300 lb4 ftA

For solution refer below images.

Answered: the force of system shown in the figure…

Engineering

Mechanical Engineering

the force of system shown in the figure below, determine the resultant and locate with respect to point A.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

Using the information in Problem 1.22, estimate the ambient air temperature that could cause frostbite on a calm day on the ski slopes. 1.22 In order to prevent frostbite to skiers on chair lifts, the weather report at most ski areas gives both an air temperature and the wind-chill temperature. The air temperature is measured with a thermometer that is not affected by the wind. However, the rate of heat loss from the skier increases with wind velocity, and the wind-chill temperature is the temperature that would result in the same rate of heat loss in still air as occurs at the measured air temperature with the existing wind. Suppose that the inner temperature of a 3-mm-thick layer of skin with a thermal conductivity of 0.35W/mKis35C and the air temperature is 20C. Under calm ambient conditions the heat transfer coefficient at the outer skin surface is about 20W/m2K (see Table 1.4), but in a 40-mph wind it increases to 75W/m2K. If frostbite occurs when the skin temperature drops to about 10C, do you advise the skier to wear a face mask? What is the skin temperature drop due to the wind?
1.22 In order to prevent frostbite to skiers on chair lifts, the weather report at most ski areas gives both an air temperature and the wind-chill temperature. The air temperature is measured with a thermometer that is not affected by the wind. However, the rate of heat loss from the skier increases with wind velocity, and the wind-chill temperature is the temperature that would result in the same rate of heat loss in still air as occurs at the measured air temperature with the existing wind. Suppose that the inner temperature of a 3-mm-thick layer of skin with a thermal conductivity of 0.35 W/m K is and the air temperature is . Under calm ambient conditions the heat transfer coefficient at the outer skin surface is about (see Table 1.4), but in a 40-mph wind it increases to . (a) If frostbite occurs when the skin temperature drops to about , do you advise the skier to wear a face mask? (b) What is the skin temperature drop due to the wind?
Direction: Show your complete solution and box you final answer. Do not round off in between the solutions but round off your final answer to the nearest ten thousandths place(4 decimal places). 1. A fluid enters a machine at 170 m/s, 800 kPa, and with a specific volume of 0.3 m^3/kg. The radiation heat loss is 25 kJ/kg. The internal energy decreases by 495 kJ/kg. If the fluid leaves at 330 m/s, 138 kPa, and 0.95 m^3/kg, determine the work done by the fulid in kJ/kg.
An air-cooled condenser has an expected U value of 30 W/m2∙K based on the airside. The condenser is to transfer 60 kW with an airflow rate of 15 kg/s entering at 35°C. If the condensing temperature is to be 48°C, what is the required airside area in m2? Round your answer to 2 decimal places.
THERMODYNAMICS (ALREADY ANSWERED IN BARTLEBY. PLEASE CHECK IF THEIR ANSWER IS CORRECT) UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG EXPLANATION NEEDED. USE 3 DECIMAL PLACES. BOX THE FINAL ANSWER. A pump discharges into a semi spherical tank at the bottom and cylindrical on top with a radius of 2 meters, and a total tank height of 8 meters. The flow rate is 80 gallons per minute and fluid specific gravity= 1.1. Determine the following: A) flow rate in kg/sec and time it takes to fill the tank in hours. B) the weight in tons of the liquid if full tank local gravity is 32.1 ft/sec squared. C) volume of the tank in metric gallons. D.) how many drums will be needed to transfer all of the tank contents (tank being full) to the drums?
MECHANICAL ENGINEERING UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. SHOW THE STEP-BY-STEP PROCESS WITH SHORT COMMENT/EXPLANATION. ANSWER IN 4 DECIMAL PLACES. Two gaseous streams containing the same fluid enters a mixing chamber and leaves as a single stream. For the first gas the entrance conditions are A1=500 cm², v1=230 m/s, p1=1.60 kg/m³. For the second gas the entrance conditions are A2= 300 cm³, m2=8.84 kg/s, v2=0.502 m³/kg. The exit stream conditions is v3=130 m/s and v3=0.437 m3/kg. Determine the following: (a) the total mass flow leaving the chamber (kg/sec) (b) the velocity of the gas at 2. (m/sec)
An air-cooled condenser has an expected U value of 30 W/m2∙K based on the airside. The condenser is to transfer 60 kW with an airflow rate of 15 kg/s entering at 35°C. If the condensing temperature is to be 48°C, what is the required airside area in m2? Round your answer to 2 decimal places. heat transfer
ques 4 plz provide handwritten step by step answer asap
Water is flowing through a pipe with an inside diameter of 4 inches. The volumetric flow rate is 24 GPM (gallons per minute). Determine the average velocity of the water in the pipe in ft/s. Group of answer choices 0.547 0.613 0.388 0.784
THE FINAL ANSWER SHOULD BE 10.75 m^3/s. Include cancellation of units and solve completely
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG EXPLANATION NEEDED. USE 3 DECIMAL PLACES. BOX THE FINAL ANSWER. A pump discharges into a semi spherical tank at the bottom and cylindrical on top with a radius of 2 meters, and a total tank height of 8 meters. The flow rate is 80 gallons per minute and fluid specific gravity= 1.1. Determine the following: A) flow rate in kg/sec and time it takes to fill the tank in hours. B) the weight in tons of the liquid if full tank local gravity is 32.1 ft/sec squared. C) volume of the tank in metric gallons. D.) how many drums will be needed to transfer all of the tank contents (tank being full) to the drums?
Please show step by step solution not just answers and how each value is derived dont just mention from a table becuase i cant fnd it, if mentioned please display it.