This is Engineering Mechanics- Static of Rigid Bodies. Solution must include FBDs. #1 DIRECTION: Solve and Analyze the following problems in neat and orderly manner.All problem solutions must include FBDS.aulosa blosb-lsaaoi n lo e nogoo leoisvACTIVITY 2: Methods of Joint1. Determine the force in each member of the truss. State if the members are intension or compression.-4 ft4 ftD.450 lb4 ftA

Answered: Image /qna-images/answer/4532f0e9-c086-4d7d-a27a-33deacc5cb37.jpg

DIRECTION: Solve and Analyze the following problems in neat and orderly manner. All problem solutions must include FBDS. a losa blob-lea e aoien ln atnogoo lsoisv ACTIVITY 2: Methods of Joint Determine the force in each member of the truss. State if the members are in tension or compression. 1. 4 ft- 4 ft D 450 lb 4 ft

DIRECTION: Solve and Analyze the following problems in neat and orderly manner. All problem solutions must include FBDS. a losa blob-lea e aoien ln atnogoo lsoisv ACTIVITY 2: Methods of Joint Determine the force in each member of the truss. State if the members are in tension or compression. 1. 4 ft- 4 ft D 450 lb 4 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Prove that the truss is statically determinate and calculate the internal forces in each truss member using the method of joints or the method of sections for a load of F=350N with workings.
FINAL ANS in : 2 Decimal places Determine the maximum axial force developed in members ID, DE, and KL of the truss shown below due to a dead load of 15 kN/m, 35 kN/m live load and the load induced by the vehicle described below. Assume loads are applied directly to the truss and moves to the right only (one-way traffic), and Load P = 13 kN.
Determine the crippling load for the “T”section of length 5m when it is used as a strut with both ends hinged. E=2.0x105 N/mm2
A solid brass [E = 109 GPa] axial member is loaded and supported as shown. Segments (1) and (2) each have a diameter of 27 mm and segment (3) has a diameter of 13 mm. Assume L1 = 1.8 m, L2 = 1.0 m, L3 = 1.7 m, R = 38 kN, Q = 14 kN, and P = 24 kN. Determine:(a) Determine the axial force in section (2) in kN. (b) Determine the deflection of joint D (positive if downward) with respect to the fixed support at A. (c) Determine the maximum normal stress in the entire axial member. Give answer in MPa.
1.Three wheel loads roll as a unit across a 12m span. The leads are A-10 kN B-20 kN to the right of A: and C-40k to the right of B. Determine the magnitude of the resultant and show its distance from point A in the figure. 2.A truss joint shown consist of a button chord made up of two angles, and web members A and B each carrying the given loads. Determine the magnitude of the resultant and its inclination with respect to the horizontal. Locate the resultant in the given figure.
In the loaded truss shown, AB=BC=CD=DE=3.4 m, BF=CG=GI=DH=HJ=(EK)/2=5.1 m. If the loading P=3.3 kN, calculate the force (in kN with proper sign) in member HK (correct to 1 decimal place). (sign convention: tensile force in a member is taken with positive sign)
For the truss shown below, applied loads are PB = 73 kN, PC = 36 kN and PD = 15 kN. Using the sign convention 'tension positive', select the correct answer for the axial force in member GH in kN: К F AR G В Рв 4@3m=12m O 1. The axial force in member GH is -60 kN. O2. The axial force in member GH is -78 kN. O 3. The axial force in member GH is -67.1 kN. Н Pc J D Ро K E 4m ?
2.) The Pratt roof trusses are uniformly spaced every 3.60 m. The deck, roofing material, and the purlins have an average weight of 0.15 kN/m^2. The building is located in the hills where the anticipated wind load is 2.10 kN/m^2. The wind load is assumed act perpendicular towards the top chord of the roof (side AHG only). Considering the given loads, determine the following: a.) Equivalent concentrated load on Joint A, H, G, F and E due to dead load b.) Equivalent concentrated load on Joint A, H and G due to wind load c.) Force in each member due to dead load and wind load. Neglect the weight of the truss members and assume A is pinned and E is a roller
Given the Truss as shown below with load P1 = X N and P2 = 3X N. Using Method of Joints, determine the following if the maximum force at member CG is 62.50 N (Compression). a.) The Load P1 . b.) The Load P2 . c.) The Force at Member GF.
For the given girders of the frame shown which carries a uniform load of 14.6 kN/m along span GH and HI and a unifoem load of 33.8 kN/m along soan DE and EF Dimensions are given as follows: A=3.7m B=5.9m C=7.5m Using the approximation frames under vertical loads. Compute the value of the absolute moment at reaction B. (kN-m) Answer: 46.7 Need solution
subj: civil engineering A 50-mm diameter bar is used as a simply supported beam 3 m long. The flexural stress is limited to 50 MPa. If w = 36. •Find Fb(bottom) and Ft(top). (F = Mc/I) •Plot the flexural stress and draw a shear & moment diagram.
Engineering Mechanics (Upvote will be given. Please write the complete solutions legibly. Box the final answer. Round to the nearest whole number. Include negative sign if DOWNWARD/COMPRESSION and positive if UPWARD/TENSION) For the truss shown, compute the following: A. Reaction at H (assume horizontal direction), Reaction at G (vertical component) and Reaction at G (horizontal component) . B. Compute for the internal forces for all members of the truss shown: Members AC, AB, CE, BC, BD, BE, DF, DE, DG, EF, EH, and FG.