Answered: Discuss the relation between the head…

Engineering

Mechanical Engineering

Discuss the relation between the head pressure and flow rate for the benefits of connecting the pumps in series?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter37: Air Distribution And Balance

Section: Chapter Questions

Problem 20RQ

See similar textbooks

Related questions

Q: 11. Water at 65 F is pumped to a tank through a 750 ft 12-in diameter galvanized iron pipe

A: Given:Length of pipe=750 ft =228.6 md=12 in =0.3048 mVolume flow rate, Q=5 cfs =0.1415 m3/s

Q: I have a pump that rotates at 1800 RPM, it pumps at a net head of 50 meters a flow rate of 80 lpm,…

Q: If the net positive suction head (NPSH) requirement for the pump is not satisfied, then, Select one:…

A: ANSWER = (a) cavitation will formed.

Q: QUESTION 02 Consider a single acting triplex pump having 7-in. liners and 12-in. stroke length…

Q: Explain the working principle of the submersible pump with neat diagram

A: A submersible pump is a pump that is able to be placed underwater and still carry out its intended…

Q: List down the different types of pumps together with its application. Classify them into Positive…

A: There are two types of pump: 1). Rotodynamic pump(Centrifugal pump)or Non-positive displacement pump…

Q: Effect of vane angle of a pump head against discharge,using equation and diagram 12:16

A: following is the answer to above question-

Q: Enumerate the different classifications of pumps

A: There are mainly two types of pump : 1. Dynamic pumps 2. Positive displacement pump 1. Dynamic…

Q: What is high pressure pump?

A: High-pressure pumps generate a very high pressure of fluid supply. Generally, high-pressure pumps…

Q: What hp must be supplied to pump 2 cu. ft per sec from the lower to upper reservoir if the pump…

A: Flow rate, Q=2 ft3/secPump efficiency, η=75%Roughness of the pipe, e=0.003 ftElevation at lower…

Q: 1. List major differences between nonpositive displacement and positive displacement pumps.

A: To find :- Difference between non positive displacement versus positive displacement pump.

Q: What is the difference between centrifugal pump and reciprocating pump ? Give at least eight points.

A: Following is the comparison between the centrifugal pump and the reciprocating pump : Centrifugal…

Q: IF THE IMPELLER OF A CENTRIFUGAL PUMP IS KEPT THE SAME AND THE SPEED VARIED, THE PUMP OUTPUT SHALL…

A: With the same impeller specifications (i.e, Diameter) and change in speed:- 1) Flow rate is…

Q: Pump charecterishics Curve halm), esyetem curve Q (mi/s) Q Pz # Show the location of operating point…

A: Location of operating point of the pump arrangement system-

Q: Determine the NPSH available for the system shown. The pump takes water at 30 ° C. The system is…

A: Water temperature, T = 30o C Static head, Hs = 2 m Length of pipe, L = 6 m Pipe diameter, d = 5 cm =…

Q: If the net positive suction head (NPSH) is greater than the required suction head of the pump,…

A: If NPSH (net positive suction head) available is greater than the NPSH required than cavitation will…

Q: Determine the wrong statement A)Pumps can decrease the velocity depending on its design…

A: Statement A is wrong.

Q: Explain the usefulness of the tubes around the pody of the commercial pump, explain it in detail

A: A pump moves liquid, but it does not create pressure. It generates the flow required for the…

Q: If the NPSHR is 3m less than the NPSHA you got on question number 2, determine the pump suction…

Q: Figure shows two possible locations for a water pump in a piping system that pumps water from the…

A: Net positive suction head (NPSH) can be defined as the measurement of fluid's pressure on the…

Q: If the net positive suction head (NPSH) requirement for the pump is not satisfied, then_ Select one:…

A: NPSH is the property of the pump and it is defined as the difference between the available NPSH at…

Q: The pump with the characteristics given in Problem 15.50 is to be used for the piping sys- tem shown…

Q: A rotary pump draws oil from (tank 1) and delivers it into (tank2), the level in (tank 1) is 3 m…

Q: subcooled? Determine (b) the volume flow rate, and (c) the

A: Given: Refrigerant R22 Condenser temperature=42oC Evaporating temperature =0oC To determine:…

Q: Write relation of dynamic head with co-efficient of discharge.

Q: estimate the volume flow rate of water through the siphon

A: Given data: Apply Bernoulli’s equation between the free surface of the tank and the exit of the…

Q: Head developed by a centrifugal pump is Select one: O a. Proportional to diameter of impeller only O…

A: Head developed by a centrifugal pump is proportional to the diameter of impeller and speed of the…

Q: A centrifugal pump takes brine from the bottom of a supply tank and delivers it into the bottom of…

A: Volume flow rate Q=400 gal/min=0.0252361m3/s h=150 ft length of pipe, L=600 ft Diameter for 4 in…

Q: Calculate the discharge throug

A: To find Discharge

Q: 3. Describe the different parts of radial flow reaction turbine.

A: Describe different parts of reaction turbine

Q: the diameter of the suction pipe is 385mm. The diameter of the discharge pipe is 268mm. If…

Q: (d) What influences the pressure developed by a pump when it is operating, and also the maximum…

A: (d). What influence the pressure developed by a pump when it is operating,and also maximum pressure…

Q: efine and discuss the important parts of the Duplex Pump.

A: defination a pump with two cylinders especially : one whose plungers are driven directly by the…

Q: Explain what is meant by a hydraulically balanced vane pump. How is this accom- plished?

A: INTRODUCTION : A vane pump is a positive displacement pump which is use to maintains a constant flow…

Q: Pumps are rated by its maximum O a. pressure,speed and flow. O b. output flow and spee in rpm O C.…

A: Pumps are rated so that the standardization of the performance of the pump can be done on the basis…

Q: Ex2-The two pumps (n=1800 rpm) each have the following characteristics: h= (100, 90, 80, 60, 40,…

Q: in fully developed laminar flow (1-4r2/D²), whereris the radi

Q: Explain and draw the right procedure of suction piping installation for a negative lift and positive…

A: Installation: You can either bring in a manufacturer-authorized technician to do the installation or…

Q: When choosing the optimal pump, the operating point should be kept close to

Q: A centrifugal pump takes brine from the bottom of a supply tank and delivers it into the bottom of…

A: Given: Difference in the level of the supply tank and discharge tank: →Z2-Z1=150 ft Length of the…

Q: Calculate the following: 1.Head at the discharge side,m 2. Velocity Head, m 3. Total Head of the…

Q: Q:/ Discuss the relation between the head pressure and flow rate for the benefits of connecting the…

A: For solution refer below images.

Q: Discuss the relation between the head pressure and flow rate for the benefits of connecting the…

A: When the two pumps are connected in series, their resultant pump performance curve is given by…

Q: In single operations, characterize a single double-acting pump

A: Single-acting pumps discharge on either the forward or reverse stroke of the piston or plunger;…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

Q/ Discuss the relation between the head pressure and flow rate for the benefits of connecting the pumps in series?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Discuss the relation between the head pressure and flow rate for the benefits of connecting the pumps in series?
Draw Head –Capacity curve of centrifugal pump at varying pumping speeds.
Write relation of dynamic head with co-efficient of discharge.
Select the number and type (ns ) of centrifugal pumps for a pumping station that must deliver 130 m3/s against a head of 50 m at 180 rpm. Assume NPSH on pumps is +5 m. Use identical single-stage pumps in parallel. Ans. 110 pumps
estimate the volume flow rate of water through the siphon
How to work out a Bernoulli pipe diameter change to increase or decrease flow into a Ram pump drive pipe. The ram pump selected is a: RAM PO400 with a 80mm drive pipe, will deliver 19200 liters per day to 125m The elevation of ram pump is 334m The elevation of drive inlet pipe is 359m The height being pumped to is 111m
Calculate the power supplied to the pump shown if its efficiency is 75%. Water is at 25 degrees Celsius is flowing at the rate of 50.0 m3/h. The suction linf is a standard DN 100 Schedule 40 steel pip, 15m long. The total length of DN 50 Schedule 40 steel pipe in the discharge line is 200m. The elbows are tight, the entrance to the pipe is flush and the globe valve is completely open. Draw the line of total and piezometric heights.
A centrifugal pump takes brine from the bottom of a supply tank and delivers it into the bottom of another tank. The brine level in the discharge tank is 150 ft above that in the supply tank. The line between the tanks is 600 ft of 4-in. Schedule 40 pipe. The flow rate is 400 gal/min. In the line are two gate valves, four standard tees, and four ells. What is the energy cost for running this pump for one 24-h day? The specific gravity of brine is 1.18, the viscosity of brine is 1.2 cP, and the energy cost is $400 per horsepower-year on a basis of 300 d/yr. The overall efficiency of pump and motor is 60 percent.
QUESTION 1:A centrifugal pump consists out of an impeller, diffuser and casing and is powered by 300kW (shaft power) and rotates at 96.3 rad/s. The flow rate generated by the machine is54.7 Kilo-litres/min. The impeller blade inlet angle and width is 23° and 180 mmrespectively. The blades occupy 12% of the impeller area and the water is assumed toenter the impeller radially. Suction and delivery pipes are equal in size.Determine:1.1The impeller inlet (i) diameter and inlet blade velocity.(Hint - Substitution: ln in terms of D and U, in terms of D, both sub into Tan of Blade inlet angle,only unknown is then solving for Dz)1.2.If the pump has a mechanical efficiency of 80%, calculate the blade velocity atoutlet (U.) and outlet whirl velocity Vw.. Assume the blade exit angle equal to theguide vane angle. (Hint - Substitution: Write Vw in terms of U, sub in Euler equation onlyunknown then is solve for Vwo)1 3Impeller outer diameter.1.4,If the flow through velocity is consistent through the…
A single suction centrifugal pumps delivers 25ft3/s of water at a head of 12m and running at 650rpm. What is the specific speed of the pump in rpm? Ans. 4380.75
What type of a pump would be most suited to delivering 30 cfs against a head of300 ft. when rotating at 480 rpm? What would the impeller diameter be?Ans: Centrifugal; 53 in.
A centrifugal pump takes brine from the bottom of a supply tank and delivers it into the bottom of another tank. The brine level in the discharge tank is 150 ft above that in the supply tank. The line between the tanks is 600 ft of 4-in. Schedule 40 commercial steel pipe. The flow rate is 400 gal/min. In the line are two gate valves, four standard tees, and four ells. The specific gravity of brine is 1.18, the viscosity of brine is 1.2 cP, and the energy cost is $400 per horsepower-year on a basis of 300 days per year. The overall efficiency of pump and motor is 60 %. What is the fanning friction factor, using the churchill equation? What is the loss factor for a wide open gate valve? What is he loss factor for a standard tee ?