How to work out a Bernoulli pipe diameter change to increase or decrease flow into a Ram pump drive pipe. The ram pump selected is a: RAM PO400 with a 80mm drive pipe, will deliver 19200 liters per day to 125m The elevation of ram pump is 334m The elevation of drive inlet pipe is 359m The height being pumped to is 111m

How to work out a Bernoulli pipe diameter change to increase or decrease flow into a Ram pump drive pipe. The ram pump selected is a: RAM PO400 with a 80mm drive pipe, will deliver 19200 liters per day to 125m The elevation of ram pump is 334m The elevation of drive inlet pipe is 359m The height being pumped to is 111m

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter34: Emission Control Diagnosis And Service

Section: Chapter Questions

Problem 2RQ: What will result from too little EGR flow? And what can cause a reduction in the flow?

See similar textbooks

Similar questions

The water is pumped from a 40 sch pipe that has 750 ft lenght, 6 in. nominal diameters. Height difference between exit and entry planes is stated as 50 ft. The yield of waterpump, 80% the power of pump motor is 20 horsepowers. Friction losses are stated as 50ft-lbf/lbm. Please calculate the flow rate in pipe line.
QUESTION 1:A centrifugal pump consists out of an impeller, diffuser and casing and is powered by 300kW (shaft power) and rotates at 96.3 rad/s. The flow rate generated by the machine is54.7 Kilo-litres/min. The impeller blade inlet angle and width is 23° and 180 mmrespectively. The blades occupy 12% of the impeller area and the water is assumed toenter the impeller radially. Suction and delivery pipes are equal in size.Determine:1.1The impeller inlet (i) diameter and inlet blade velocity.(Hint - Substitution: ln in terms of D and U, in terms of D, both sub into Tan of Blade inlet angle,only unknown is then solving for Dz)1.2.If the pump has a mechanical efficiency of 80%, calculate the blade velocity atoutlet (U.) and outlet whirl velocity Vw.. Assume the blade exit angle equal to theguide vane angle. (Hint - Substitution: Write Vw in terms of U, sub in Euler equation onlyunknown then is solve for Vwo)1 3Impeller outer diameter.1.4,If the flow through velocity is consistent through the…
Q/ Discuss the relation between the head pressure and flow rate for the benefits of connecting the pumps in series?
Pump at its best efficiency point(BEP) has a capacity of 12500 gpm while developing a head of 60ft at a rotative speed of 1450rpm. What is the specific speed of the pump? ANSWER: 7520rpm
A pump draws benzene at 25°C from a tank whose level is 2.6 m above the pump inlet. The suction line has a head loss of 0.8 N-m/N. The atmospheric pressure is mea- sured to be 98.5 kPa(abs). Find the available NPSH. The vapor pressure of benzene is 13.3 kPa.
Consider a positive displacement pump; Shaft speed is 1800rpm Pump push 0.003gal/revolution Leakage is 5% of the flow for a pressure of 3000 psi. The pressure and flow at the loadside are rrealted according to the following equation p = 68Q² Q = gal per min P = psi Wat is the operating point of the pump
A pumping system has the following characteristics, f=0.015 length of thepipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipeis cast iron, and the system curve is:Hp= 34+ 5.47Q2Knowing that the system curve and the pump curve intersect at 12 cfsa. Determine Operation headb. Determine dischargec. Plot the system curve
The suction diameter of 60mm reads 2psi vaccum and 50mm diameter discharge with 250kpag. The suction water level is 5m above water pump center line and discharge water level is 25m above the pump center line. The total head loss at suction and discharge is 2m. If discharge is 0.01m3/s, find the horsepower needed to pump the water for 80% pump efficiency. ANSWER: 8.15 hp
Water is to be pumped at a head of 142 ft, the water temperature being 100°F and the barometric pressure being 14.3 psi. At intake, the pressure is a vacuum of 15 in Hg snd the velocity is 13 fps, what is tge net positive suction head (NPSH)?
Francis and Kaplan turbines are often provided with drafttubes, which lead the exit fl ow into the tailwater region, asin Fig. . Explain at least two advantages in using adraft tube.
A centrifugal pump consists out of an impeller, diffuser and casing and is powered by 300 kW (shaft power) and rotates at 96.3 rad/s. The flow rate generated by the machine is54.7 Kilo-litres/min. The impeller blade inlet angle and width is 23° and 180 mmrespectively. The blades occupy 12% of the impeller area and the water is assumed toenter the impeller radially. Suction and delivery pipes are equal in size. Determine: a) If the pump has a mechanical efficiency of 80%, calculate the blade velocity at outlet (Uo) and outlet whirl velocity Vwo. Assume the blade exit angle equal to the guide vane angle. (Hint - Substitution: Write Vwo in terms of Uo sub in Euler equation only unknown then is solve for Vwo)
2. A centrifugal pump consists out of an impeller, diffuser and casing and is powered by 300 kW (shaft power) and rotates at 96.3 rad/s. The flow rate generated by the machine is54.7 Kilo-litres/min. The impeller blade inlet angle and width is 23° and 180 mmrespectively. The blades occupy 12% of the impeller area and the water is assumed toenter the impeller radially. Suction and delivery pipes are equal in size. Determine:2.1. The impeller inlet (i) diameter and inlet blade velocity. (Hint - Substitution: Vfi in terms of Di and Ui in terms of Di both sub into Tan of Blade inlet angle, only unknown is then solving for Di2) 2.2 If the pump has a mechanical efficiency of 80%, calculate the blade velocity at outlet (Uo) and outlet whirl velocity Vwo. Assume the blade exit angle equal to the guide vane angle. (Hint - Substitution: Write Vwo in terms of Uo sub in Euler equation only unknown then is solve for Vwo 2.3 Impeller outer diameter. 2.4 If the flow through velocity is consistent…