Discuss traditional drawing and Computer-Aided Drawing

Q: Projections drawing?

A: Solution:   The Top, Front and Side view are shown below:

Q: Explain the yield phenomenon and yield strength by drawing graphics.

A:

Q: The design was made as a consequence of which six directions were given to the paper factory?

A: In our everyday lives, paper is essential, and it has been for a very long time. Wood pulp is…

Q: What are the steps for drawing?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Explain the disadvantages of Tube Drawing process in which mandrel is not used.

A: Given Data⇒Tube drawing ProcessNo use of mandrelProblem definition⇒Problem says Explain the…

Q: What is a pictorial drawing? What are the different types of pictorial drawings?

A:

Q: Explain the disadvantages of Tube Drawing process in which mandrel is not used.

A: The tube drawing process that reduces the tube diameter without using a mandrel is known as tube…

Q: Explainthe advantage of corner radii of punch and die in Sheet Metal Drawing Process.

A: The corner radii of punch and die is very important in sheet metal drawing process because the radii…

Q: Tandem drawing of wires and tubes is necessary because; Surface finish improves after every drawing…

A: Given question 1 question 2

Q: Describe, using sketches, the possible metal forming process that could have been used to produce…

A: The shown fig can be produced with the help of the extrusion process. The extrusion process may be…

Q: 7) Sometimes Drawing crimps are used in deep drawing process for producing complex shapes. Why?

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: * Which defect arises due to small Punch force in sheet drawing operations? O Tearing O Wall…

A:

Q: Compare any ten major differences between Drawing process and Extrusion process

A: Following is the differences between Drawing process and Extrusion process- Extrusion Drawing…

Q: How do you work with Sketch in SOLIDWORKS?

A: Given:- Solidworks software To find:- How to create a sketch and work in it

Q: 6. Compare the forming processes of wire drawing, conven- tional extrusion, and continuous extrusion…

A: 6) PARAMETER   WIRE DRAWING CONVENTIONAL EXTRUSION             Reduction in area less more…

Q: (a) Explain the advantage of corner radii of punch and die in Sheet Metal Drawing Process.  (b)…

A: Corner radii: The corner radii is the curved corner of any shape as shown in the figure below.…

Q: Describe how curves and surfaces are transformed. while discussing computer-generated art,

A: A curve is a collection of points that is indefinitely big. Aside from endpoints, every point has…

Q: Describe in detail the development of Computer Aided Drafting.

A: The use of computers (or workstations) to help in the development, revision, analysis, or…

Q: ; It is proposed to use an axisymmetric drawing operation to reduce the diameter of a cylindrical…

A:

Q: Describe the concepts behind principal components and dimensionality reduction.

A: given; Describe the concepts behind principal components and dimensionality reduction.

Q: In a two-stage wire drawing operation, the fractional reduction (ratio of change in cross- sectional…

A:

Q: DISCUSS THE SIGNIFICANCE OF DRAWING TO INDUSTRY.

A: Soln:- drawings are important because they are used to communicate the technical details of a…

Q: Hello. Would it be possible to include detailed explanations in every step? Thank you.

A: Given: Two springs are opposite to each other and by the energy stored in spring A is transferred by…

Q: Explain the importance of lubrication in wire drawing

A: Wire drawing Wire drawing is the process in which metal is pulled out through die using tensile…

Q: Q#4:(a) Explainthe advantage of corner radii of punch and die in Sheet Metal Drawing Process.

A: Corner radii are important in sheet metal drawing process because the radii of punch and die avoid…

Q: Differentiate ISOMETRIC DRAWING to OBLIQUE DRAWING.

A:

Q: what is Deep Drawing?

A:

Q: It is proposed to use an axisymmetric drawing operation to reduce the diameter of a cylindrical rod…

A: Calculated the minimum number of drawing stages needed to reduce diameter of cylinder from Do to…

Q: In the deep drawing of cups, blanks show a tendency to wrinkle up around the periphery (flange). The…

A: Explanation: Wrinkling is a type of defects which occurs in the deep drawing operation . Wrinkling…

Q: Explain the difference between deep drawing and redrawing

A: Deep drawing Deep drawing is a process in which a sheet metal blank is drawn into the forming die…

Q: (a) Explain the advantage of corner radii of punch and die in Sheet Metal Drawing Process. (b)…

A: (a) Sheet metal drawing process This is a type of forming process in which metal in the form of…

Q: 1- The use of lubricant in wire drawing die.

A: we have to discuss the use of lubricant in wire drawing

Q: 1. In the manufacture of automotive-body panels from carbon-steel sheet, stretcher strains (Lueders…

A: Given question : How can stretcher strains be eliminated? How wrinkles in deep drawing operation can…

Q: Explain with neat sketch, the surface finishing process of “Sandblasting

A:

Q: Projections drawing؟ ?

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: Properties of areas of common shapes.

A: The area of some the common shapes with their properties are as follows, Circle: The property of a…

Q: Hello. Would it be possible to get a more detailed solution? Thank you

A: Given: There are angular acceleration present for the disc along with some rotational speed. And we…

Q: Enumerate the steps taken in creating the objects.

A: Solution:

Q: ow do you work with Sketch in SOLIDWORKS?

A:

Q: 2. A paper below has a shear strength of 10 MPa. What must be the applied force to cut the paper…

A: