Đ T₂ The car is being towed by two ropes at angles α₁ = 20° and a₂ = 30°. The car travels in a straight line with constant velocity as shown, the resultant of its frictional rolling resistance is F₁ = 1500 N. Find T₁ and T₂. f 1 Axis F₁ α ₂ α

Đ T₂ The car is being towed by two ropes at angles α₁ = 20° and a₂ = 30°. The car travels in a straight line with constant velocity as shown, the resultant of its frictional rolling resistance is F₁ = 1500 N. Find T₁ and T₂. f 1 Axis F₁ α ₂ α

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Question # 2: Describe the practical applications of consolidated-drained analysis for clay soil.

A: The consolidated-drained analysis for clay soil is used for determining the drained shear strength…

Q: Consider the beam given in the figure. Given: X=0.3 in, E=30,000 kips/in², and/= 240 in 4. NOTE:…

A: E = 30000 kip/in.2 I = 240 in.4 Determine the support reaction and draw the shear force and moment…

Q: Assume that, due to a construction error, the beam of the previous two examples was placed…

Q: how is water facilities and other utilities can be targets of terrorist acts

A: The critical role they play in supporting communities makes water facilities and other utilities…

Q: The shear leg derrick is used to haul the m = 200 kg net of fish onto the dock. Assume the force in…

Q: For the activity on node shown below, find the critical path and the expected duration of the…

Q: A 20 m long concrete pile with a rectangular cross section of 460 mm × 460 mm fully embedded in sand…

Q: Compute the reactions for the beam in the given figure. The reaction for the beam at A is RAD The…

Q: Please find the forces in members using method of joints

Q: How will you improve the bearing capacity of a weak soil mass?

Q: Problem #1: Determine the moment of inertia of the composite area about the y-axis and the the…

Q: Given an adjustment containing the following: Number of Control Stations 1 Number of Unknown…

Q: A two-story office building totaling 18783 ft2 is interpreted as a light hazard (200 ft2/sprinkler…

A: A two-story office buildingArea= 18783 ft2Hazard level: light hazardMaterial: SteelTo determine:Size…

Q: Determine the force in members BC, and state if these members are in tens compression. 2 kN A 4 kN B…

Q: Explain the geological difference between Metallic and Non Metallic minerals. Discuss also the…

A: The geological difference between Metallic and Non-Metallic Minerals:Point of ComparisonMetallic…

Q: The data in the table below is for a closed-polygon traverse. Balance the traverses by coordinates…

A: CourseLengthBearingAB403.73N 8o17'02"EBC622.63N 87o02'05"ECD653.16S14o47'06"WDA550.84N 68o43'20"W

Q: *9-4. Determine the reactions at the supports, then draw the moment diagram. Assume the support at A…

Q: Use ASD to determine the width of the 5/8 inch thick A36 plate subjected to tension as shown below.…

A: ASD5/8 inch thick A36 platedead load, PD=85 kiplive load ,PL=80 kipTwo rows of 5/8 inch standard…

Q: A stream 84 ft. wide carries 60 cfs. Determine the resulting head over a Cipolletti weir 3 ft high…

Q: Please recheck Ra and Rb is actually equal to 6kn and not 15kn

A: As per the given question, we have to check the reactions at supports. Original question was: A beam…

Q: A beam is subjected to the loading condition shown below. Determine the displacement at A and the…

A: “Since you have asked for multiple methods, we will provide the solution only using the second…

Q: L B Determine the reaction at the roller support and draw the bending moment diagram for the beam…

Q: A 2 1⁄2 - in. fire hose discharges water through a nozzle having a jet diameter of 0.97 in. the lost…

Q: m? Select an answer and submit. For keyboard navigation, use the up/down arrow keys to select an…

Q: SHOW THE ILLUSTRATION/DIAGRAM AND COMPLETE SOLUTION. 2. Two tangents intersects at an angle of…

Q: Consider the beam and loading with M= 12 kN/m shown in the figure. Vertex M A Parabola 8 m- B…

Q: Determine coordinates of centroid of the shaded area shown in figure. All dimensions are in mm. 40…

Q: Consider the beam given in the figure. Given: X= 18 kN and Eis constant NOTE: This is a multi-part…

Q: 1500N/m Calculate the magnitudes of the reactions at A, B, and C for the frame shown. Neglect the…

Q: 7-18. Determine the slope at D and the displacement at the end A of the beam. El is constant. Use…

Q: A developer is building a 60-unit apartment building. Construction will take 15 months covering all…

A: To calculate the forecasted vacancy rate for Year 1 in the pro forma, consider the leasing schedule…

Q: The plate shown below represents a rock core with total length of core bit = 110 cm and the length…

Q: PROBLEM 10.2: A 3m wide wall footing supports a 300mm wall. It is reinforced with 20mm bars with…

Q: 1. Two tangents converge at an angle of 19°34'49". The second tangent is due east. The distance of…

A: Note : Since you have asked multiple questions, we will solve the first question for you. If you…

Q: A mason art dam has a pervious and as foundation determine the maximum permissible upward gradient.…

A: For a masonry dam,To find maximum permissible upward gradient

Q: nigunt. mit signt is connected to the wall by a pin at ♬ and also supported by member BE. Support…

Q: Determine the permissible ultimate moment capacity Mn of the prestressed bonded beam shown in…

A: The yield strength of the prestressed tendons is fpy=240000 psi.The ultimate strength of the…

Q: Figure Q1 shows a frame which is fixed at the base A, pinned at C and fixed at the wall E. The frame…

Q: derive the formulas for midspan deflection for propped cantilever support conditions

Q: Problem #3: Plot the shear and moment diagrams for the shown beam. What are the values of the shear…

Q: Water at T = 25°C is drawn from an underground detention tank and discharged into a drain using a…

Q: For the beam shown below, use your preferred method and determine: a. The reactions at the supports…

Q: Following are the results obtained from a plate load test performed on a square plate of 30 cm x 30…

Q: The rectangular channel shown in the following figure has a width of 11 ft and transports water at…

A: The total of the kinetic and potential energies per unit weight of the fluid determines the specific…

Q: Q1: The following time distribution of the rainfall, estimate the -Index and W- Index of the…

A: As the value lies between 0.5 and 0.6 the assumption is correct

Q: 9-14. Determine the reactions at the supports, then draw the moment diagram for each member. EI is…

Q: -12/Compute the flow rate of irrigation water Q to

Q: What is the minimum water depth in a very wide channel with longitudinal slope of S=0.005 and mean…

Q: A beam of length 10 m is simply supported and carries point loads of 5 kN each at a distance of 3 m…

A: Given:Length of beam = 10 m5kN Point load is at 3m and 7m from left support UDL of 1kN/m between…

Q: 29 (WP The wooden box beam shown in Figure P9.29a is fabricated from four boards fastened together…

A: Resistance by each nail = 800Nmaximum shear force = 9 kNTo find:maximum permissible spacing interval

Concept explainers

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.

Question

Axis
F₁
(FO) (-)
a
2
α₁
T₁
T₂
The car is being towed by two ropes at angles α₁
= 20° and a₂ = 30°. The car travels in a straight
line with constant velocity as shown, the resultant
of its frictional rolling resistance is F₁ = 1500 N.
Find T₁ and T₂.
1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduce the problem statement

VIEW

Step 2: Calculate the value of T1 and T2.

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

- Block B has a mass m = 10 kg and is released from rest when it is on top of the cart A, which has a mass of 3m. Determine (a) the tension in cord CD needed to hold the card from moving while B slides down A, and (b) the acceleration of A and B. The coefficient of kinetic friction between A and B is µk = 0.2 and let θ = 37º.
Consider a vehicle being towed with a rope up a hill at constant velocity, and therefore in equillibrium. The vehicle has a mass of 1500 1500 kg (i.e. weight of 14.715 kN14.715 kN) that acts at the center of mass at GG. The contact between the inclined road and wheels at AA and BB are smooth, and the tyres are free to roll, so rolling resistance can be neglected. The angle θθ between the rope and the road is 5 degrres. Calculate the tension in the rope. Calculate the total net reaction force on the rear tyres at A. the towing arrangement and towing angle are changed so that the front wheels of the car are just lifted off the road. Calculate the new tension in the rope and new angle θθ made between the rope and the road.
If a torque of M = 300 N ⋅ m is applied to the flywheel, determine the force that must be developed in the hydraulic cylinder CD to prevent the flywheel from rotating. The coefficient of static friction between the friction padat B and the flywheel is μs = 0.4.
If the beam AD is loaded as shown, determine the horizontal force P which must be applied to the wedge in order to remove it from under the beam. The coefficients of static friction at the wedge’s top and bottom surfaces areμCA = 0.25 and μCB = 0.35, respectively. If P = 0, is the wedge self-locking? Neglect the weight and size of the wedge and the thickness of the beam.
The block brake consists of a pin-connected lever and friction block at B. The coefficient of static friction between the wheel and the lever is μs = 0.3, and a torque of 5 N ⋅ m is applied to the wheel. Determine if the brake can hold thewheel stationary when the force applied to the lever is(a) P = 30 N, (b) P = 70 N.
: Block B has a mass m and is released from rest when it is on top of cart A, which has a mass of 3kg. Determine the tension in cord CD needed to hold the cart from moving while B slides down A. Neglect friction. =30o
A uniform bar AB is resting in a horizontal position on smooth inclines as shown below. Determine the load P that will hold the bar in equilibrium. Also, determine the reactions at A and B. Wherein: Q=2 T=6 Example: 2QT kN = 226 kN T.Q5 m = 4.25 m
A shaft turning at a uniform speed carries two uniform discs A and B of masses 10kg and 8kg respectively. The centres of the mass of the discs are each 2.5mm from the axis of rotation. The radii to the centres of mass are at right angles. The shaft is carried in bearings C and D between A and B such that AC = 0.3m, AD = 0.9m and AB = 1.2m. It is required to make dynamic loading on the bearings equal and a minimum for any given shaft speed by adding a mass at a radius 25mm in a plane E. Determine: The distance of the plane E from plane A The dynamic loading on each bearing when the mass in plane E has been attached and the shaft rotates at 200 rev/min. For the bearing loads in the opposite direction determine all the unknown values. For the bearing loads in the same direction, show the diagrams and equations only to use for a possible solution. PS – Use graphical methods to solve the…
A conveyer belt is used to transfer granular material and the frictional resistance on the top of the belt is F = 500 N. Determine the smallest stretch of the spring attached to the moveable axle of the idle pulley B so thatthe belt does not slip at the drive pulley A when the torque M is applied. What minimum torque M is required to keep the belt moving? The coefficient of static friction between the belt and the wheel at A is μs = 0.2.
The mass of body A is 45 kg. The coefficient of frictionfor bodies A, B, and the ramp C is 0.10. Neglectingfriction between the string and the ramp, determinethe smallest mass of B for which equilibrium of thesystem exists. show fbd and complete solution
Blocks B has a mass of 20 kg and block C has a mass of 15 kg. The coefficient of static friction at the contacting surfaces is 0.2. Block A is suspended by arope that passes over a fixed cylinder and is attached to block B. The coefficient of static friction between the rope and the cylinder is 0.25. What is the largest mass block A can have without causing block B to slip the left?
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=75° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm2 and A=50 cm2 shall be taken for all rods.)