Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the bending moment 3.2 m to the right of point Aif W = 11.5 kN/m, T = 17.55 kNm, m = 10.4 m, and n = 5.4 m. Round off the final answer to four decimal places.

Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the bending moment 3.2 m to the right of point Aif W = 11.5 kN/m, T = 17.55 kNm, m = 10.4 m, and n = 5.4 m. Round off the final answer to four decimal places.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A gantry crane of weight W=100 Kg moves across a bridge with the length I=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles.
Please Help me to answer this... For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=6.5 ft, b=24.0 ft, P = 32 kips and w = 9.5 kips/ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. Determine the bending moment acting at each of the following locations:(a) x = 6.5 ft (i.e., at point B)(b) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the bending-moment sign convention detailed in Section 7.2. Use your shear-force and bending-moment diagrams to determine the maximum bending moment, Mmax, and its location, xmax. Use the bending-moment sign convention detailed in Section 7.2.Answers:
find the maximum value Mmax of the bending moment
A gantry crane of weight W=100 Kg moves across a bridge with the length /=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles. So it’s wrong answer 1136 N can anyone how to solve for it different ?
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let w = 4.0 kips/ft, a= 6.5 ft, and b= 17.5 ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.
At a full draw, an archer applies a pull of 130 Nto the bowstring of the bow shown in the figure. Determinethe bending moment at the midpoint of the bow.
For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 1.14 in from the bottom of the beam on a section 2.89 feet to the right of B if P = 2314 lb, Q = 8345 lb, w = 1.33 in, L = 7.92 in, b = 3.85 in, and h = 1.41 in. Round off the final answer to two decimal places.
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown below if P = 1639 N, T = 4678 Nm, a = 0.75 m, b = 1.07 m, c = 0.94 m, w = 44 mm, and h = 75 mm . Round off the final answer to one decimal place.
A beam is carrying a moment M as indicated. The cross section of the beam is symmetric about the z axis. The dimensions of the cross section and the location of the centroid (point C) are shown. Knowing that Iy = 280,000 mm4, Iz = 150,000 mm4, and M = 400,000 + UV in N.mm, where UV is 21(a) Calculate the components of the bending moment on the y and z axes, Myand Mz.(b) Identify which point at the cross section has the largest tensile stress, and which point at the cross section has the largest compressive stress.(c) Calculate the maximum tensile stress and the maximum compressive stress in the cross section
A vertical loads of 400 N acts at the end of a horizontal rectangular cantilever beam 2 m long and 25 mm wide. If the allowable bending stress is 130 MN/m^2, find the depth of the beam in mm
For the beam shown, calculate the magnitude of the bending stress (in psi) at the bottom of the beam on a section 1.17 feet to the right of B if P = 2044 lb, Q = 8215 lb, w = 1.16 in, L = 8.09 in, b = 3.69 in, and h = 1.1 in. Round off the final answer to two decimal places.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=3.5 ft, b=9.0 ft, c=4.0 ft, d=3.5 ft, w = 5.5 kips/ft and P = 45 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. For this loading, calculate the reaction forces Ay and Ey acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Ay =___________ kips, Ey = __________ kips. Determine the shear force acting at each of the following locations:(a) x = 0+ ft (i.e., just to the right of support A)(b) x = 3.5 ft(c) x = 12.5 ft(d) x = 16.5– ft (i.e., just to the left of D)(e) x = 16.5+ ft (i.e., just to the right of D)(f) x = 20.0– ft (i.e., just to the left of support E) Answer: a to f ) V = ________ kips Use the graphical…