Draw the shear force and bending moment diagrams of the cantilever beam shown using METHOD OF AREAS. Determine the maximum shear force and maximum bending moment. Note that there are internal hinges at C and E. A 15 kN/m 120 kN THC PAKE 10 kN/m E↓↓↓↓ ↓↓ F B D Hinge Hinge 8 m---5 m-+-5 m--5 m-+-5 m--8 m- ~~ 3 G ENGETA

Draw the shear force and bending moment diagrams of the cantilever beam shown using METHOD OF AREAS. Determine the maximum shear force and maximum bending moment. Note that there are internal hinges at C and E. A 15 kN/m 120 kN THC PAKE 10 kN/m E↓↓↓↓ ↓↓ F B D Hinge Hinge 8 m---5 m-+-5 m--5 m-+-5 m--8 m- ~~ 3 G ENGETA

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design a purlin for a roof truss having the following data:Span of the truss = 6.0mSpacing of truss = 3m c/c.Inclination of roof = 30oSpacing of Purlin = 2m c/cWind pressure = 1.5 kN/m2Roof coverage= A.C Sheeting weighing 200 N/m2Provide a channel section Purlin.
: At a cross section in a T-beam with flange width b= 600 mm,effective depth d=375 mm, flange thickness hf=125 mm, width of web bw=200mm,flexural reinforcement=4T32, Design ultimate shear force V = 157.5 kN. Determine thespacing of 10 mm diameter links. Assume fcu= 30 N/mm2, fyv=250 N/mm2 fcu=30N/mm2
a0 () o 2 20210612.. > A beam is constructed from three boards nailed together as shown in Fig. . If each nail can support a shear force of 45 Ib. if the largest vertical shear of 100 lb for the beam, determine the maximum spacing s of the nails for each case (a) and (b) il 3 > mil (€ 3in osin ™, 0sin » t | |« osin | osin 6in 6in ¥ 05in 1 0sin case (a) case (b)
A built-up beam made from fastening two channels to a wide flange section carriesloads` as shown. The fasteners are 12mm∅ bolts with allowable shear stress τ= 110 MPa. Forbearing, σb= 220MPa for single shear, and σb= 275 MPa for double shear. E=200 GPA. Fy=420MPa. Do not round off between solutions . Explain the Stepsa.) Determine the Moment of Inertia of the Sectionb.) Determine the Moment Capacity of the section if fb≤280MPa
The overhanging beam shown supports the given ultimate load Wu= 5okN/m. The section is 300mm by 500mm rectangular beam having f'c=35MPa, fy=420 MPa, stirrups diameter = 10mm and concrete cover 40mm. a.) the area of steel reinforcement corresponding to rho max in mm2.b.) the location of the point of zero shear in the beam measured from the left support B in mm.c.) Calculate the maximum positive moment in the beam in kN.m.d.) Calculate the required reinforcement Asreqd corresponding to the maximum positive moment in mm2.e.) Calculate the depth of the compression block of the final positive moment section in mm.f.) Calculate the depth of the neutral axis of the final positive moment section in mm.g.) What is the ultimate moment capacity of the final positive moment section in kN.m.h.) Calculate the additional positive moment that can be imposed to the beam without exceeding the moment capacity of the final positive moment section in kN.m.
Match supports to reaction forces provided. Roller: Pin or knife edge: Fixed: a. b. c.
At-beam has a width of flange equal to 700mm and a thickness of 100mm. It has an effective depth of 450mm and the width of the web section is 350mm. It is reinforced at the bottom with a steel area of 2925sq.mm. fc'=17.24MPa, fy=413.7MPa. The depth of the compression block is _mm. A. 136.00mmB. 146.00mmC. 126.00mmD. 156.00mm
An axially loaded column W360 x134 hasits weak axis braced at the third points.The overall length of the column 8 m. UseA 572 grade 50 Fy=345 MPa. The columnis pinned connected at both ends.Properties: rx = 155 mm, ry = 95 mm,A = 17,105 mm2 Determine the slenderness ratio withrespect to y-axis. Determine the slenderness ratio withrespect to x-axis. Determine the critical slendernessratio. What is the nominal compressivestrength of the steel column?
16 -The stair beam in the figure will have support reactions. A support is a fixed, B support is a sliding joint. loads P1= 15 kN, P2= 30 kN, dimensions a = 2 m, b = 6 m, c = 4 m. Accordingly, Bx = ?A) 3.75B) None.C) 18.75D) 0E) 30
Question:- A 7.5 meters long simply supported structural steel beam carries two concentrated loads P at every third points. Use A 572 Grade 65 steel with Fy=448.18 MPa. The beam is W310x23.8 section having the given properties. A=3040mm² d= 305mm tw= 5.6mm bf=101mm tf= 6.7 mm Ix= 43x10⁶ mm⁴ Iy=1.2x10⁶mm⁴ a) Calculate the allowable bending stress of the compression flange of beam 7.5 fully supported against lateral movement. b) Based from the previous question, calculate the value of concentrated load P that the beam could support safety.
A column section b = 400 mm, h = 600 mm is reinforced with longitudinal bars Ast = 8-ϕ25 mm equally distributed along all faces. Lateral ties are composed of 12 mm rectangular hoops with clear cover equal to 40 mm and 12 mm cross ties in both directions. Concrete yield strength f’c = 27 MPa and steel yield strength, fy = 415 MPa.Calculate the nominal axial strength of the column in kN.A. 7 047 B. 5 638C. 4 580 D. 6 342 Calculate the center to center spacing of ties for confinement.A. 200 B. 400C. 500 D. 300 Where is the plastic centroid measured from the short edge of the column?A. 200 B. 400C. 500 D. 300 Calculate the steel stress (MPa) in the middle layer of bars at balanced strain condition.A. 31.37 comp B. 43.52 compC. 31.37 tension D. 43.52 tension Calculate the nominal axial strength in kN of the column at balanced strain condition considering bending about the strong axis.A. 3,420 B. 2,500C. 2,875 D. 3,846
The riveted lap connection shown consists of two(2) – PL 12 mm × 280 mm. 1. If allowable bearing stress in holes is 1.2Fu where Fu is the ultimate strength of the plate and which is equal to 400 MPa, find the maximum allowable force P that can be applied neglecting effect of eccentricity. a. 563.3 kN b. 460.8 kN c. 683. 6 kN d. 405.9 kN 2. If allowable yielding of gross area is Fy/1.67, where Fy is the yield strength of the plate and which is equal to 250 MPa, find the maximum allowable force P that can be applied neglecting effect of eccentricity. a. 534 kN b. 560 kN c. 446 kN d. 503 kN 3. If diameter of hole equals diameter of rivet, what is the net area of edge-3-4-edge in square millimeters? a. 2540 b. 2590 c. 2880 d. 2040