Draw the single line diagram of a substation having the following equipments: . i) Incoming lines: Two, 110kV ii) Outgoing lines: (a) One, 110kV (b) Four, 11kV iii) Transformers: (a) Two, 10MVA, 110/11kV, D/Y (b) One, 2MVA, 11kV/ 415V,Y/Y e ● iv) Bus-bars: 110kV-Duplicate bus-bar, 11kV single bus-bar Show the positions of CTS, PTs, isolators, lightning arresters, circuit breakers.

Draw the single line diagram of a substation having the following equipments: . i) Incoming lines: Two, 110kV ii) Outgoing lines: (a) One, 110kV (b) Four, 11kV iii) Transformers: (a) Two, 10MVA, 110/11kV, D/Y (b) One, 2MVA, 11kV/ 415V,Y/Y e ● iv) Bus-bars: 110kV-Duplicate bus-bar, 11kV single bus-bar Show the positions of CTS, PTs, isolators, lightning arresters, circuit breakers.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16MCQ: With generator conyention, where the current leaves the positive terminal of the circuit element, if...

See similar textbooks

Similar questions

Draw the single line diagram of a substation having the following equipments: i) Incoming lines: Two, 132kV ii) Outgoing lines: (a) Five, 132kV (b) Five, 33kV iii) Transformers: (a) One, 25MVA, 132/33kV, D/Y (b) One, 2MVA, 33kV/ 420V,Y/Y iv) Bus-bars: 132 kV-Duplicate bus-bar, 33kV single bus-bar Show the positions of necessary equipments that using for protections, measurements and
Draw the single line diagram of a substation having the following equipments:i) Incoming lines: Two, 132kVii) Outgoing lines: (a) Five, 132kV (b) Five, 33kViii) Transformers: (a) One, 25MVA, 132/33kV, D/Y (b) One, 2MVA, 33kV/ 420V,Y/Yiv) Bus-bars: 132 kV-Duplicate bus-bar, 33kV single bus-barShow the positions of necessary equipments that using for protections, measurements and communications.
A 120 MVA, 19.5 kV generator has Xs = 0.15 per unit and is connected to a transmission line by a transformer rated 150 MVA, 230 Y/18Δ kV with X = 0.1 per unit. If the base to be used in the calculation is 100 MVA, 230 kV for the transmission line, find the per unit values to be used for the transformer a. 0.06667 b. 0.1467 c. 0.05 d. 0.0405
Draw a 66KV Overhead Transmission Tower with all engineering details.
An electrical lineman is connecting three single-phase transformers in a Y(primary)-Y(secondary) configuration, for power service to a business. Draw the connecting wires necessary between the transformer windings, and between the transformer terminals and the lines: Note: fuses have been omitted from this illustration, for simplicity.
Refer to the 5-bus data given below. Sbase = 400 MVA, the base voltage is 15.0 kV for buses 1 and 3, and 345 kV for buses 2, 4, 5. Note that 1-5 and 3-4 are 15/345 kV transformers.a) Draw a one-line diagram of the power system.b) Find the elements Y23, Y43, Y11 Y33 of the system bus admittance matrix.
Q4 / Equipment ratings for the four - bus power system shown in Figure are given as follows: TI 73 60 500 Generator GI: 500 MVA, 13.8 KV. X = X2 = 0.20. Xo = 0.10 per unit Generator G2: 750 MVA, 18 KV.X = X2 = 0.18, Xo = 0,09 per unit Generator G3: 1000 MVA, 20 kV, X = 0.17. Xz = 0.20.Xo = 0.09 per unit Transformer Ti: 500 MVA, 13.8 kV A / S00 kV Y. X = 0.12 per unit Transformer T2: 750 MVA, 18 LV A / 500 kV Y, X = 0.10 per unit Transformer T3: 1000 MVA, 20 kV A / 500 kV Y. X = 0.10 per unit each line: X = 50 ohms, X, = 150 ohms 77 The inductor connected to generator G3 neutral has a reactance of 0.028 pu. Draw the zero-, positive-, and negative - sequence reactance diagrams using a 1000 - MVA, 20 - KV base in the zone of generator G3
Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire service, and having the following loads: 2-1.5hp A/C, 2-1.0hp A/C, 1-0.5hp water pump, 4-800W water heater, 2-6kW electric range and 2-1kW microwave oven, determine the total connected load in volt-ampere (VA). Write your answer in numerical format without decimal places.
Draw (400KV) Overhead Transmission Towers with all engineering details.
1. What are the applications for stripline and microstrip transmission lines? 2. Give 2 examples of characteristic impedance application for each stripline and microstrip transmission lines.
A 500kVA distribution transformer serving the KTU has full load iron loss of 2.5kW and copper loss of 3.5KW during a day, its loading cycle for 24hours is as follows:--6hours, 200kW at 0.8 lagging being total loads consumed in the administration-10hours, 150kW at 0.7lagging, being total loads used in staff bungalows- 5hours, 600kW at 0.8 lagging, being total loads consumed in the Faculty of Engineering Calculate ALL-DAY efficiency of the transformer above. (b) State (2) two purposes of oil in a transformer
Solve for each individual line current and the total complex power.