Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire service, and having the following loads: 2-1.5hp A/C, 2-1.0hp A/C, 1-0.5hp water pump, 4-800W water heater, 2-6kW electric range and 2-1kW microwave oven, determine the total connected load in volt-ampere (VA). Write your answer in numerical format without decimal places.

Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire service, and having the following loads: 2-1.5hp A/C, 2-1.0hp A/C, 1-0.5hp water pump, 4-800W water heater, 2-6kW electric range and 2-1kW microwave oven, determine the total connected load in volt-ampere (VA). Write your answer in numerical format without decimal places.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.60P: PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06...

See similar textbooks

Similar questions

Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire service, and having the following loads: 2-1.5hp A/C, 2-1.0hp A/C, 1-0.5hp water pump, 4-800W water heater, 2-6kW electric range and 2-1kW microwave oven, determine the rating of feeder overcurrent protection in ampere-trip (AT) using inverse time circuit breaker. Write your answer in numerical format without decimal places.
(1) Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire service, and having the following loads: 2-1.5hp A/C, 2-1.0hp A/C, 1-0.5hp water pump, 4-800W water heater, 2-6kW electric range and 2-1kW microwave oven, determine the total connected load in volt-ampere (VA). (2) Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire service, and having the following loads: 2-1.5hp A/C, 2-1.0hp A/C, 1-0.5hp water pump, 4-800W water heater, 2-6kW electric range and 2-1kW microwave oven, determine the rating of feeder overcurrent protection in ampere-trip (AT) using inverse time circuit breaker. Write your answer in numerical format without decimal places
Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire be service, andhaving the following loads: 2-1.5hp A/C, 2-1.0hp A/C, 1-0.5hp water pump, 4-800W water heater, 2-6kWelectric range and 2-1kW microwave oven, determine a) the total connected load, b) the total demand load,c) the overall %demand factor, d) the size of THW feeder conductor, ground wire and IMC conduit, e) therating of feeder overcurrent protection using inverse time circuit breaker
a fifty unit apartment building has a 4.5-kW electric clothes dryer in each apartment. by using the optional method, what is the service demand load?
What is the maximum length in km for 3 phase transmission line having conductor of 0.875 square centimeter area over which 220kW at unity power factor and 3500V are to be delivered? The efficiency is 80% and specific resistance is 1.825 micro cm.:
Determine the current in the neutral conductor and the current in each line conductor (i.e., IR, IB andIY) using the given information below. The powers 12 kW, 18 kW and 24 kW are the loads of a purely resistive loads which are between the yellow and blue, the red, and neutral phases respectively of a 3-Φ, four-wire system.415 V is the line voltage. Find the active power (in kW) in the main network and in. each branch and the apparent power (in kV A) using the given information below. Two branches connected in parallel had a p.d. of 200∠30° V applied to them. The currents in the respective branches are 20∠60° A and 40∠30° A. Thanks
In a 380 kV three-phase transmission system, the diameter of the overhead lines in the form of cylinder conductors is 28 mm. a) How much distance should there be between two conductors using the maximum area calculation equations? Calculate. (Puncture peak strength of air is 30kV / cm.) b) In this configuration, if the distance between phase conductors is 4 m, at what voltage level Calculate the discharge occurs? c) Maximum electric field in the same configuration, for electrode distances to be 8 m Calculate the value. If needed in calculations Ꜫ0 = 8.854x10-12 F / m
estimate the distance over which the load of 15000 KW at 0.85 power factor can be delivered by a three phase transmission line having conductors of Steel coated aluminium each of resistance 0.905 ohm per face per kilometre the voltage of the receiving end is to be 132 KV and the losses in transmission is to be 7.5 % of a load
"A 75-ohm load terminates a 50-ohm transmission line. The point of reflection is at the load. If the measured incident voltage at the point of reflection is 10 Vrms, what is the total voltage at the load? Enter only the numerical value. No need for the unit. Use four decimal places (if the answer is not an integer)."
50 km of single-phase transmission line, 800 kVA power 8 kV, is carried with 0.9 reverse power factor. The resistance of one kilometer of the line is 42 mΩ, and the reactance of one kilometer of the line is 0.646 Ω. Find the voltage at the beginning of the line and the efficiency of the line accordingly.
What is the maximum length in km for 1 phase transmission line having conductor of 0.875 square centimeter area over which 220kW at 0.8 power factor and 3500V are to be delivered? The efficiency is 80% and specific resistance is 1.825 micro cm
Company Y would like to have a new installation transmission line to open a small new city consist of 300 MW with 0.85 power factor lagging at full load. The new transmission line required 132 kV with 124.274 miles long. All the elements needed for the new transmission line is listed in table shown in the picture. You are required to model the transmission line and analysed the performance of the new transmission lines in terms of voltage regulation and efficiency. Note that the frequency used is 50 Hz.