ductile material having an endurance limit of 196 N/mm² and the yield point at 294 N/mm² is stressed under variable load. The maximum and minimum stresses are 147 N/mm2 and 49 N/mm² The fatigue stress concentration factor is 1.32 .what is the

ductile material having an endurance limit of 196 N/mm² and the yield point at 294 N/mm² is stressed under variable load. The maximum and minimum stresses are 147 N/mm2 and 49 N/mm² The fatigue stress concentration factor is 1.32 .what is the

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.7.5P: Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight...

See similar textbooks

Related questions

Q: A seamless cylinder with a storage capacity of 0.025 m² is subjected to an internal pressure of 20…

A: Given, Volume of cylinder = V = 0.025 m3 Internal pressure = P = 20 MPa Ultimate strength of…

Q: Lo=80 mm, Copper Alloy C93200 (bearing bronze), T1=20 C, T2=75 C. dL=?, Lf=? Copper Alloy C93200…

A: we know that change in length by thermal expansion = coefficient of thermal expansion…

Q: If the application temperature is about 900 C, and strength requirement is between 100 ksi~150 ksi

A: We can obtain the required zone by drawing perpendiculars at the respective coordinates , to get the…

Q: A rod of length 1.6m long has a diameter of 0.5m wide. this rode is made of 52100 chromium steel…

Q: Select the lightest W shape that will act as a column of 7 m long with both end hinged and support…

Q: D) Discuss the main parameters Effect the Fatigue life.

A: Note:- As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: 1. hot-rolled bars of AISI 1020 and 1040 steel 2. stainless steel sheets of Type 430 ferritic…

A: Solution:: Ans-1 The separation of metal parts occurs according to two different processes: ferrous…

Q: (a) The dependence of failure modes on temperature. (b) The effect of temperature changes and stress…

A: From the given graph for Izod impact test and creep test results for nylon thermoplastic polymer, We…

Q: n ductile materials occurs when the stresses at the crack tip ation factors for ductile materials…

A: a) factor of safety is always used while designing a components ( True) b) small radius of…

Q: Suppose you have a 4340 steel plate in fully variable axial loading with an axial load ranging from…

Q: Is Euler buckling failure initiated by an elastic, plastic, or cracking process? Explain.

A: Euler buckling failure: The column's buckling failure is said to be Euler buckling failure if the…

Q: How are the modes of failure readily defined?

A: The modes of failure are prediction theories. According to these theories, the solid material fails…

Q: A cylindrical component will be designed with a circumferential notch to accommodate a small snap…

A: Given data: Depth of notch, d = 1 mm Notch radius, r = 0.5 mm Now calculating the theoretical…

Q: If the material is ductile and subjected to a static load , is it not necessary to use stress…

A: It is not necessary to use stress concentration factors for ductile material under static loading…

Q: A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is to be subjected to a tensile load.…

A: GivenLength of rod L = 500 mmDiameter of rod d = 12.7 mmIn this question , there is two condtions…

Q: A support rod for the landing gear of a private airplane is subjected to a tensile load during…

A: Given data: F=40000 lbffos=4 Need to determine the minimum required area and material.

Q: A 200-mm-long polypropylene rod, with a rectangular cross-section that is 20 mm by 4 mm, is…

A: Given: The length of the rod, L = 200 mm The area of the rod, A = 4x20 = 80 mm^2 The load acting on…

Q: What is the stress concentration factor for a part under axial load with a shoulder fillet if…

Q: A bar of circular cross-section is subjected to alternating tensile forces varying Example 4 from a…

Q: There are two approaches used for determining the o-N behavior of a material subjecte letely…

Q: As part of your job, your role is to investigate the behavior of a hydraulic system. This apparatus…

A: The system is used to test a sample by rupturing it. A hydraulic system is used to provide enough…

Q: ductile material having an endurance limit of 196 N/mm² and the yield point at 294 N/mm² is stressed…

A: Given:Endurance limit=196 N/mm²yield point stress=294 N/mm²maximum stress=147 N/mm2minimum stress=49…

Q: Describe a metal fatigue failure. (b) What two distinct types of surface areas are usually…

A: Crack initiation is the most common initial step of fatigue failure. When the applied stress…

Q: cylindrical rod 500 mm long, having a diameter of 12.7 mm, is subjected to a tensile load of 30,000…

A: Given, L = 500 mm d = 12.7 mm P= 30,000 N

Q: A ductile material having an endurance limit of 196 N/mm2 and the yield point at 294 N/mm² is…

A: Given, Endurance limit = SE = 196 N/mm2 Yield limit = Sy = 294 N/mm2 Maximum stress = σmax = 147…

Q: The aluminum shell is FULLY bonded to the brass core, and the assembly is unstressed at a…

A: according to the above given detrails

Q: B) A machine part is made of forged steel with Su = 630 MPa, S'. = 0.5 Su. Estimate the life cycles…

A: When external load acting on a component is not static, but varying in magnitude with respect to…

Q: Problem 1: Which metal and or metal alloy material will not experience either plastic deformation or…

A: Given: L= 380 mm load P= 24500 N

Q: To manufacture a piston with a circular cross section, an alloy steel bar is required whose length…

A: Given: Piston with circular cross section Length of piston bar, L = 35mm Compression load = 5.2 tons…

Q: (d) A support rod for the landing gear of a private airplane is subjected to a tensile loading…

Q: Required information A gap of 0.02 in. exists between the composite rod and the wall when the…

A: GIVEN DATA BRONZE AND ALUMINIUM ROD IS GIVEN WE HAVE TO FIND TEMPRATURE AT WHCIH IN ALUMNIUM ROD…

Q: If a key material has an ultimate strength of 120 ksi and a yield strength of 80 ksi and factor of…

Q: If a key material has a yield strength of 80 ksi, and a safety factor N= 2, what would be the design…

Q: An aluminium rod of circular cross section is to withstand 250kN of tensile load for a structural…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: Is the Paris power law (Eq. 10-3) relevant for all conditions of fatigue crack growth?

A: Paris' law (also known as the Paris–Erdogan equation) is a crack growth equation that gives the rate…

Q: a) The principal stresses experienced by a component are -100 MPa and 150 MPa. If a safety factor of…

Q: 11.A cylindrical bronze pin of 1 mm radius rests on a rotating steel disk at a mean radius of 25 mm.…

A: Given data ; W=10N mass loss of pin = 50 mg mass loss of disk = 3 mg Radius of steel disk = 25 mm…

Q: Determine the tensile and yield strengths for the following materials: (a) UNS G10200 hot-rolled…

A: The tensile strength of a material is the maximum force required to break the material. or we can…

Q: A bar of circular cross-section is subjected to alternating tensile forces varying from a minimum of…

Q: 82. A machine component made of a ductile material is subjected to a variable loading with omin =-50…

Q: If a constant-stress load cycle is periodically interrupted by an anomalously large stress cycle,…

A: Fatigue lifetime Generally, it is a mechanical term used for the measurement of the lifespan of a…

Q: how is fatigue resistance measured

A: Fatigue resistance is determined by the method of SN curve (Fatigue life).

Q: A theater rigging company uses a safety factor of 10 for all its ropes, which means that all…

Q: Discuss the measures that could be adopted to extend the fatigue life of the structure.

A: Given question: Discuss the measures that could be adopted to extend the fatigue life of the…

Question

A ductile material having an endurance limit of 196 N/mm² and the yield point at 294 N/mm² is stressed under variable load. The maximum and minimum stresses are 147 N/mm2 and 49 N/mm² The fatigue stress concentration factor is 1.32 .what is the available factor of safety for this loading?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
A ductile material having an endurance limit of 196 N/mm² and the yield point at 294 N/mm² is stressed under variable load The maximum and minimum stresses are 147 N/mm² and 49 N/mm² The fatigue stress concentration factor is 1.32 What is the factor of safety for this loading?
A steel rod with a cross-sectional area of 180 mm2 is stretched between two fixed points. The tensile load at 25°C is 3,600N. Assume thermal coefficient equal to 11.7 x 10-6 mm/ (mm°C) and E = 200 GPa. Which of the following most nearly gives the temperature at which the compressive stress will be 48 MPa? Which of the following most nearly gives the temperature at which the tensile stress will be 48 MPa? Which of the following most nearly gives the temperature at which the stress will be zero?
What causes materials to fail in fatigue at a stress less than the ultimate stress? How does this relate to the microstructure of the material?
Consider a cylindrical specimen of a steel alloy (Figure 6.22) 8.5 mm (0.33 in.) in diameter and 80 mm (3.15 in.) long that is pulled in tension. Determine its elongation when a load of 65,250 N (14,500 lbf) is applied.
1. An aluminium rod of circular cross section is to withstand 250kN of tensile load for a structural application. The minimum length of the rod is 4.2m but must deform elastically to no more than 7mm when the tensile force is applied. Take that the engineering yield stress limit and the Young’s modulus of the material are 260 MPa and 70 GPa respectively.If a safety factor of 2 is adequate, design an appropriate rod and state why factor of safety is important in your analysis. 2. Explain the differences in the grain structure between a metal which has been cold worked and another same cold worked piece but has been fully re-crystallised. Why are small angle grain boundaries not as effective in interfering with the motion of dislocation as high angle grain boundaries?
Analyse the differences between the 2 attached stress-strain curves for 0.9% carbon steel and 0.15% carbon steel.
See the set of bars for made of a material that has a yield strength of 350 MPa, determine the minimum h1 and h2 dimensions required. Apply a safety factor F.S. = 1.5 without flow. Each bar is 12 mm thick
Q1:Explain creep and also explain its importance. Q:02. Why fatigue is dangerous. Explain it with some examples.
-Define the maximum shear stress theory and sketch its failure envelope.-Define the maximum shear strain energy theory and sketch its failure envelope
Is the engineering stress-strain curve or the true stress-strain curve preferred for large strains? Explain.
1. In the nominal stress-strain diagram (Figure 1), write down the names and meanings of points 1, 2, 3, and 4.2. Explain how to find the 0.2% offset yield strength, and explain the% elongation and% reduction in cross-sectional area.3. After explaining the difference between the true stress/strain and the nominal stress/strain, show the true stress-strain diagram for the nominal stress-strain diagram (Figure 1) to correspond points 1, 2, 3, and 4.