DYNAMICS OF RIGID BODIES (RECTILINEAR MOTION WITH CONSTANT ACCELERATION)  A body starts with a velocity of 3 m/s and moves in a straight line with a constant acceleration. If its velocity at the end of 5 seconds is 5.5 m/s, determine the following:(a)the uniform acceleration(b)distance travelled in 10 seconds.

Q: As a test, CJ played croquet with a 0.922-kg. mallet head and you can assume that it can be modelled…

A: given : mass of mallet mA = 0.922 Kg mass of handle mB = 0.63Kg mass of ball m= 0.42 kg length of…

Q: An ideal Rankine cycle operates between the pressure limits of 15,000 kPa in the boiler and 15 kPa…

A:

Q: Consider a 0.6-m-high and 1.2-m-wide double-pane 0.78 W/m-K) separated by a 8-mm-wide stagnant a…

A: Given data  Thickness of glass = 3mm Conductivity of glass = 0.78(W/m-k) Thickness of air gap = 8mm…

Q: A wooden beam is loaded by a concentrated load P=1000N and supported by boundary conditions shown in…

A: GivenP=1000N LAB=1600mmLBC=3400,B0=10mm,B1=20mmH=230mmh0=150mmh1=40mm

Q: QUESTION 9 A liquid cooled heat sink for a smartphone is sketched in Figure Q9. It uses water of…

A: Density ρ= 997 kg/m kinematic viscosity v= 1.19 x 10-6 m2s-1 No of tubes = 5 diameter Dh =5 mm…

Q: The figure below provides steady-state data for water vapor flowing through a piping configuration…

A: given : V₁ = 20 m/s T₁ = 360 C p₁ = 5 bar A₁ = 0.2 m²

Q: h) The figure below shows a beam supported at points A and B. The vertical force at F is 500 N and…

A: In this issue, we will determine the distance (s) necessary to balance the beam by first calculating…

Q: Steam at a pressure of 0.08 bar and a quality of 87.4% enters a shell-and-tube heat exchanger where…

A: Given that: Inlet condition of steam are, P1 = 0.08 bar and x1 = 87.4 %. Steam exits as saturated…

Q: The coal combustion in the furnace of steam power plant produces 31.52 mega-Watts (MW) of heating…

A:

Q: Above a fairing, the flow speed decelerates according to the formula U₁ = 1 - x¹.3 m-s-1, where x is…

A: Given Data A two-dimensional Laminar boundary Layer grows under the adverse pressure gradient of a…

Q: A bar of a uniform cross-section is rigidly fixed at one end and loaded by an off-centre tensile…

A: “Since you have posted multiple questions, we will provide the solutiononly to the specified sub…

Q: A fast mail delivery drone uses an ideal jet-propulsion cycle to fly in air of free-stream…

A: Given: T1 = 314K V1 = 84 m/s q3-4 = 202 kJ/kg To find: Specific thrust

Q: 1. The rigid beam ABC is supported by the pin joint at A and the steel wire BD. The wire is 0.10…

A:

Q: Consider the following ideal cascade refrigeration system with pressures of 0.9, 0.4, and 0.12 MPa.…

A: Given:High pressure condenser pressure, Pc=0.9 MPa=900 kPaIntermediate pressure, Pi=0.4 MPa=400…

Q: 1. A steam power plant has a steam turbine with an isentropic efficiency of 85%. The inlet steam…

A: GivenηT=85%P1=100 bar =10000 kPaT1=500oCP2=10 bar =1000 kPaT2=150oC

Q: Q2 (A): Derive the system of differential equations describing the straight-line vertical motion of…

A: Solution: Given Data: k1=k2=k3=1m1=m2=1x10=x20=0x.10=-1x.20=1   To Find: Derivation of the 2…

Q: Determine the (magnitude) of the moment about line AD of the 750-lb tension in cable CE. Z 3 ft 2 ft…

A: The tensile in cable CE is 750(lb) Find the magnitude of moment about line AD

Q: Theories in Structural Analysis Combined stresses: tutorial question 3** The rectangular block of…

A: Given data  The vertical force = 40kN Find the largest normal stress

Q: Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal…

A:

Q: At the bottom A of the vertical inside loop, the magnitude of the total acceleration of the airplane…

A:

Q: Consider two robot-manipulators: • A SCARA robot with joints displacement range q1,2 = −90◦...90◦…

A: Option 1 The Cartesian robot has a larger workspace is the correct statement.

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A:

Q: Which of the following will result to an increase in thermal efficiency of a steam power plant…

A: Given: Condenser and boiler operating pressure remain constant. And we know that when the mean…

Q: Confine with 1 lb of wet steam at 500 F and with an enthalpy of 800 Btu in a rigid container. Heat…

A: Given: Initial temperature, T1=500F Enthalpy at initial state, h1=800Btu dryness fraction at final…

Q: The following system is in static equilibrium with the strings AB, BC, and CD connected to support…

A: Find the tension T1 and T2

Q: Q1- A converging nozzle with a throat area of 0.001² m is operated with air at aback pressure of…

A:

Q: Find the velocity of point B and angular velocity in link 3 using relative analysis and polygon…

A: The length of links are  O2A=4'', AB=7'', O2O4=9'', O4B=8'' The angular speed of O2A is ω2=1 rad/s.…

Q: Water flows at a depth of 0.7 m and velocity of 3 m/s in a 4-m wide rectangular channel when it…

A: According to the given data Y1 = 0.7m V1 = 3 m/s B= 4m b = 5m We need to find final depth.

Q: You are requested to use SIMATIC S7-300 PLC to control the following operations on the…

A: Given: Working To find: PLC diagram

Q: describe the operation of electro-mechanical parking brake.

A: Electro-mechanical parking brake An electromechanical parking brake is a type of parking brake that…

Q: A gas cylinder with interior volume 11.6 L holds compressed air at 17.4 MPa. The cylinder is joined…

A: Given: Volume of the gas cylinder: →V1=11.6 L=0.0116 m3 Pressure in the gas cylinder: →P1=17.4 MPa…

Q: An intermediate fuel oil (?=996 ??/?3) stands 12 m deep in a storage tank whose top is open to the…

A: In this issue, we will compute the gauge pressure at the bottom of the tank by first computing the…

Q: Injuries in a workshop are often caused by incorrect lifting or moving of heavy loads. Name and…

A:

Q: 2. Determine the magnitude of the resultant force and its direction. F3 - 750 N 30 F₂ = 625 N F₁ =…

A:

Q: A bead of mass 0.1kg is bound to a linear track which connects the points (1,2,3) and (-1,2,4). The…

A: Given: F = (xy2z, x, z2) Points: (1,2,3) to (-1,2,4) To find: Work done

Q: An industrial roller door is a uniform rectangular panel made of a heavy material, y = 45 pcf, and…

A:

Q: Select from the following statements, those which describe the process and conditions required for…

A: Introduction Metals can fracture ductilely or brittlely. Metals that can withstand significant…

Q: etermine the vertical reactions at each of the two outriggers as a function of boom angle when the…

A: Given: The combine mass of crane and truck is, M=18 Mg. The mass of the boom is, m=2 Mg. The boom…

Q: The 10-kg block shown in the figure below rests on the smooth incline. If the spring is originally…

A: Given data: Mass of the block = m = 10 kg Angle of inclination of plane = 30° Distance travelled = s…

Q: 5. Find the elevation of point A in the figure shown. 0.2 kg/cm² 30 cm Hg vacuum Air water Air B…

A: Find the elevation at point A

Q: For a given part drawing (fig.2) prepares a part program for a wire electric discharge machine using…

A: For the given part drawing, we can write part program using Fanuc cut language which is based on G…

Q: Calculate the moment of inertia of the shaded area about the x-axis. Assume a - 35 mm, r - 25 mm.…

A:

Q: An existing steady state refrigerator has been operating using the vapor-compression cycle for some…

A: Given data  Cop=3.1 Find the effect of Qc and Win and choose right one.

Q: An ideal Carnot heat pump operates from a low temperature reservoir T₁-272.6 K and supplies 9.94 kW…

A:

Q: A chemicals company is looking to optimise the materials selection for their synthesis vessel with…

A: Solution: Given Data: Criteria accepted: Yield before break. The fracture toughness is, KIC=Yσπa…

Q: The water is at the pressure of 0.22 bar and temperature of 60°C. a) Using data from the table,…

A: According to the given data P = 0.22bar and T = 60 °C We need to find 1. Its state 2 Degree of…

Q: All parts please thank you so much Part b) Bending moment by real forces_1 Let the origin of the…

A:

Q: concentric-pipe heat exchanger, one of the fluids is a condensing vapour and the other is the…

A: This question is based on the concept of concentric-pipe heat exchanger.

Q: Sea 0.92 and 1.025, respectively. If a 25-cm-high portion of the ice block extends above the surface…

A:

Q: Calculate the moment of inertia of the shaded area about the x-axis. 75 mm Answer: 1x = 23 mm ·*. 38…

A:

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.