The slender 12-kg bar has a clockwise angular velocity of w = 2 rad/s when it is inthe position shown Suppose that L = 2.9 m. (Figure 1)Figure60⁰°1 of 1Part ADetermine its angular acceleration, measured clockwise.Express your answer using three significant figures. Enter positive value if the angular acceleration is clockwise and negative value if the angular acceleration is counterclockwise.α =SubmitPart BNA =SubmitPart C195| ΑΣΦ 41Determine the magnitude of the normal reaction of the smooth surface A at this instant.Express your answer to three significant figures and include the appropriate units.NB =SubmitRequest Answer0μÅValueRequest AnswerμAvecValueRequest AnswerUnitsDetermine the magnitude of the normal reaction of the smooth surface B at this instant.Express your answer to three significant figures and include the appropriate units.2Units?=?rad/s²?

Answered: e 10 | bartleby

Engineering

Mechanical Engineering

e 10

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The spool has a weight of 40 lblb and a radius of gyration kOkOk_O = 0.4 ftft . A cord is wrapped around its inner hub and the end subjected to a horizontal force PPP = 8 lblb . Assume the spool rolls without slipping. (Figure 1) Determine the spool's angular velocity, measured clockwise, in 5 ss starting from rest.
11. Box A (mass 50 kg) and box B (mass 200 kg) shown in Figure 9 are released from rest. Here the mass of pulleys is ignored. The coefficient of copper friction between box A and box B is 0.1, the coefficient of copper friction between box B and slope is 0.2, and the angle of slope is 20 degrees. Answer each of the following questions.1) Calculate the acceleration (m/s^2) of box A.2) Find the tension size (lb).3) If box A and box B are obtained when box B moves 1.0m, explain why it is not possible to apply the Principle of Work & Energy to the entire box A, box B and pulley system, and obtain the speed (m/s) of box A and box B when box B moves 1.0m down.4) When box B moves 2m, calculate the speed (m/s) of box A using the Modified energy supply law.
A motorcycle and rider have a combined mass of 350kg. The each wheel has a mass of 20kg with the diameter of 500 mm. The rider accelerates from 5m/s to 25m/s over a distance of 100m, whilst climbing a hill of slope 1 in 20. Identify the magnitude and effect of gyroscopic reaction torque by calculating the angular velocity and power as the motorcycle ascends the incline when the motorcycle and rider travel at 80 km/h around a left-hand bend of road with the radius 30 m.Explain the effects of energy transfer in mechanical systems (e.g. gears, pulley or flywheel) with uniform acceleration present.
A stepped cylinder has the dimensions R₁ = 0.30 m, R₂ = 0.65 m, and the radius of gyration, k, is 0.35 m. The mass of the stepped cylinder is 100 kg. Weights A and B are connected to the cylinder. If weight B has a mass of 80 kg, and weight A has a mass of 50 kg, how far does A move in 5 seconds? In which direction does it move? (Draw all FBDs)
A force was applied to a 50 kg wheel as shown in the figure. If the wheel starts to rest without slipping Determine the angular acceleration ε, the wheel pressure on the ground N and the rotational speed of the wheel n after 10 revolutions, if the rolling friction coefficient f = 0.1. Take the radius of inertia of the wheel equal to 0.3 m.
A spool of mass 60 kg is supported on two rollers at A and B as shown in FigureQ1(c). Neglect the mass of the inelastic cable, friction and the mass of therollers at A and B. Knowing that a constant pulling force P is applied in order tounwind 6 m of cable in 3 s starting from rest. The radius of gyration for the spoolis (604) mm, Appendix Ashows the examples of identifying the radius of gyration using student ID.(i) Determine the angular acceleration of the spool. (ii) Determine the pulling force P. (iii) Explain with calculation on ways to increase the acceleration of cablebeing pulled. [
Q1: A cylindrical body has a mass Mand outer radius R (the moment of inertia I I= 1 2 MR^ 2 ) starts to roll from rest (upper position) down on an inclined surface. If the effect of friction force was ignored, determine the linear speed of the cylinder when it hits level ground a height h lower.
Consider the system of two blocks. There is no friction between block A and the tabletop. The mass of block B is 5.00 kg. The mass of block A is 4.00 kg. The pulley rotates about a frictionless axle, and the light rope doesn’t slip on the pulley surface. The pulley has a mass of 2.00 kg and with a 0.100 m radius. The system is released from rest. (a) What is the angular speed of the pulley when block B falls 1.50 m? (The moment of inertia of the pulley = (1/2)MR^2) (b) How long does it take when block B falls 1.5 m? (block A and block B move with constant acceleration)
(c) A spool of mass 60 kg is supported on two rollers at A and B as shown in Figure Q1(c). Neglect the mass of the inelastic cable, friction and the mass of the rollers at A and B. Knowing that a constant pulling force P is applied in order to unwind 6 m of cable in 3 s starting from rest. The radius of gyration for the spool is (600+a) mm, where a =8 Explain with calculation on ways to increase the acceleration of cable being pulled
The system shown below is made up of two pulleys attached to the same shaft, with radii ri and re of 0.29 mm and 0.43 mm, respectively. The total mass of the pulley system is 14 kg and its turning radius is 0.26 mm from its center. The mass of block A is 9 kg and the mass of block B is 2 kg. If the coefficient of kinetic friction between block B and the floor is 0.2, find the angular acceleration of the pulley.
A bar of 30 kg mass is in the rest position for the position θ = 0 °, for which the spring is in its unstretched (relaxed) state. Find the angular velocity of the bar when it is at the position θ = 90 °. Take the acceleration due to gravity as 9.81 m / s ^ 2
While the system shown is in equilibrium, a counter-clockwise torque T =T0sin(ωt) N-m(with T0 = 226.6 and ω=7) is applied to teh disk. What is the disk angular speed ω0 = ? in rad/s at time t = 4.2 sec? ( I = 0.2 kg.m2, b = 7.8 N-m-s/r, k = 1,504 N/m, r = 0.52m )