The steel hollow shaft is rigidly attached to a solid bronze shaft by a bolt coupling, A maximum torque T can be applied to the ends of the shaft without failure. Use G=83 GPa for steel and G=35GPa for bronze. The steel bollow shaft is rigidly attached to a solld bronze shaft by a bolt couplingA maximum torque T can be applied to the ends of the shaft without faflure. Use G-83 GPa for steel and G-35 GPa for bronze.Determine the maximum torque T in kN-m without exceeding a shear stressof 70 MPa In steel and 50 MPa for bronze.A) 10.44Determine the maximum torque Tin kN-m without exceeding an angle oftwist of 2.5° In the 3.5-m length.A) 1.20Determine the number of 16 mm bolts required to attach the two shafts If theallowable shear stress in each bolt is 30 MPa and the diameter of bolt circle is1.B) 9.82C) 8.56D) 7.352.B) 13.51C) 2.40D) 12.683.150 mm.A) 4B) 5C) 6D) 7

Answered: Determine the maximum torque T in kN-m…

Determine the maximum torque T in kN-m without exceeding a shear stre of 70 MPa In steel and 50 MPa for bronze. A) 10.44 Determine the maximum torque Tin kN-m without twist B) 9.82 C) 8.56 D) 7.35

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

the steel hollow shaft is rigidly attached to a solid bronze shaft by a bolt coupling. a maximum torque T can be applied to the ends of the shaft without failure. use G=83GPa for steel and G=35Gpa for bronze. 1. determine the maximum torque T in kN.m without exceeding an angle of twist of 4.1 degrees in the 3.5 length. 2. if the torque T is 11.68 kN-m, calculate the maximum shear stress (MPa) in the bronze shaft. 3. if the torque T is 9.28 kN-m, calculate the maximum shear stress (MPa) in the steel hollow shaft.
+ Asteel shaft (G =77 GPa) & an (Al) tube (G = 27 GPa) are connected to a fixed support & a rigid disk at the two ends. Knowing that the initial stresses are zero, determine the max torque that can be applied to the disk if the allowable stresses are ;.. = 120 MPa & 7, = 70 MPa for the steel shaft & (Al) tube respectively Rigid Disk Al Tube R e 76 mm I | Steel Shaft 50 mm B R | 8 mm 500 mm Trube ) Steel Shaft
The shaft is made from a solid steel section AB and a tubular portion made of steel having a brass core. It is fixed at a rigid support at A and a torque T=50lb-ft is applied at C. Gsteel= 11,500 ksi Gbrass= 5,600 ksi What is the angle of twist at C? What is the maximum shear stress in the steel and brass? What is the maximum shear strain in the steel and brass?
Aluminum shaft AB [GAB = 26 GPa, LAB = 1 m, dAB = 40 mm) and Bronze shaft BC GBC = 45 GPa, LBC = 2 m, dBC = 70 mm) are fully bonded at B. The shafts are fixed at A and C, and subjected to a torque T = 8 kN-m. Determine the angle of twist at B.
1. A steel shaft is to be manufactured either as a solid circular bar or as a circular tube (Fig. 3-12). The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa nor an allowable rate of twist of 0.75%m. (The shear modulus of elasticity of the steel is 78 GPa.) a) Determine the required diameter d0 of the solid shaft. b) Determine the required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter. c) Determine the ratio of diameters (that is, the ratio d2/d0) and the ratio of the weights of the hollow and solid shafts.
The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable shear stress of 6 ksi. The diameter of the rod is d1 = 0.500 in. The outside diameter of the tube is D2 = 1.625 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod.
the trolley of a small hoist is supported on a horizontal beam as shown. the maximum mass to be lifted is 6000kg the tie back is a round rod 33 mm in diameter the tensile stress in the is not to exceed 170 MPa the maximum elongation allowed for the tie back is 2.5 mm. determine the maximum dimemnsion L permitted
A solid steel shaft ABC of 50mm diameter is driven at A by a motor that transmits +50kW to the shaft at 10Hz. The gears at B and C drive the machinery using power equal to -35kW and -15kW, respectively. Determine the maximum shear stress in the shaft & compute the angle of twist of the shaft between the motor at Ao and the gear at C. Please take note: the values are negative (-35 & -15) & G = 83 GPa
Determine the cracking moment in kN-m for the section shown if: f'c = 28MPa fr=0.7(square root of (f')(c))
The bell-crank mechanism is in equilibrium for an applied load of F1 = 19 kN applied at A. Assume a = 280mm, b = 170mm, c = 80mm, and θ = 45°. Pin B is in a double-shear connection and has a diameter of 30 mm. The bell crank has a thickness of 29 mm. Determine the bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest tenths.
The following solid aluminum bar (E = 10,000 ksi; α = 11.70E-06/F) is located between two fixed supports. Segment AB has a diameter of 3 inches and segment CB has a diameter of 2 inches. The load P is equal to 25 kip and the temperature increases by 50°F. Determine: a. The reactions at the supports. Answ: Cy = 17.938 kip (downward); Ay = 42.938 kip (upward). b. The deformation at point B. Answ: 2.693E-03 pulg. c. The stress in both segments. Anws: 5.709 ksi, 6.07 ksi.
A hollow tube ABCDE constructed of monel-metal is subjected to five torques acting in the directions shown. The tube has an outside diameter d2= 1.0in. The allowable shear stress is 14,950psi and the allowable rate of twist is 2.45degree/ft. Determine the maximum permissible inside diameter d1 of the tube in inches. Use G= 9500ksi.