i need the answer quickly Q5:- For the mechanism shown in the figure below, lengths of thevarious links are: OE=15 cm, AB=40 cm, BC=50 cm and CD=20 cm. Thecrank OE rotates uniformly at 70 rpm cw. For the configuration shownin the figure, determine :- (a) velocity of the die block in the slot of thelever AB, (b) liner acceleration of point B, (c) linear acceleration ofpoint C, (d) Coriolis component of acceleration of point E and (e)angular acceleration of link BC.60°5 cm20 cm30 cm

Answered: Image /qna-images/answer/10a6a821-a5b5-43a1-a7d6-d2ccf13790d2.jpg

Answered: E 60° 5 cm 20 cm 30 cm

Engineering

Mechanical Engineering

E 60° 5 cm 20 cm 30 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q#03 : In a four-bar chain ABCD, Link AD is fixed and is 160 mm long. The crank AB is 40 mm long and rotates at 150+25 rpm clockwise. While Link CD is 70mm long and oscillates about point D. BC and AD are of equal length, angle BAD=60°. Find the angular velocity of Link CD? (Subject : mechanics of machines)
The system shown in the figure is composed of bar AB which is pin-supported at A and attached to bar BC. The end of bar BC is connected to the slider block C. At the instant shown, the acceleration of point B is 1.125 m/s2 downward and the angular velocity of bar BC is 0.5625 rad/s counterclockwise. What is the angular speed of bar AB?
Consider the slider-crank mechanism shown. Crank AB is 0.500 m long and is rotating counterclockwise at 3.00 rad/s. Rod BD is 1.500 m long. 1. Which of the following gives the closest value of the speed of end B of crank AB? 2. If crank AB is rotating at a constant angular velocity, which body/bodies is/are in general plane motion?
The device in the figure, B and C are pins, the center disk C rolls without sliding on the contact D, and the bar 4 slides inside the guide 5, whose pin A is mounted on the bar OB. Angular velocity ω1 and a known angular acceleration ?1 are known. At the instant shown, find: a) The angular velocity of the bar 4 b) The angular acceleration of bar BC Data: OA = ?, AB = 2?
In a four-bar chain ABCD. AD is fixed and is 150mm long. The crank AB is 90 mm long and rotates at 120 rpm clockwise while the link CD is 80 mm long and oscillates about D. BC and AD are of equal length. Find the angular velocity of link CD, when angle BAD = 60O. a) Draw the configuration diagram in appropriate scale. b) Determine the angular velocity (ωAB). c) Determine the linear velocity (Vba) d) Draw the velocity diagram in appropriate scale. e) Determine the linear velocity (Vcb), , and f) the angular velocity (ωcd)
The system shown in the figure is composed of bar AB which is pin-supported at A and attached to bar BC. The end of bar BC is connected to the slider block C. At the instant shown, the acceleration of point B is 1.125 m/s2 downward and the angular velocity of bar BC is 0.5625 rad/s counterclockwise. What is the angular acceleration of bar BC?
(Three-Dimensional Motion) The figure below represents a pair of bevel gears A and B. Gear A rotates in ahorizontal plane about a vertical axis at O. Gear B rotates around the shaft OC,which in turn rotates about the terminal axis at O. At the instant shown, theangular velocity of the shaft OC is 10j rad/sec, and gear A is stationary. Deter-mine the angular velocity of gear B, and the velocity of a point D at the top ofgear B.
In a swiveling joint mechanism, as shown in figure below, the driving crank OA is rotating clockwise at 200 r.p.m. The lengths of various links are: OA - 50mm; AB = 350 mm; AD = DB; DE = EF = 250 mm and CB - 125 mm. The horizontal distance between the fixed points and C is 300 mm and the vertical distance between F and C is 250 mm. For the given configuration, determine: 1- Velocity of the slider block F 2. Angular velocity of the link DE. And 3. Velocity of sliding of the link DE in the swivel block
Given a fourbar linkage (not drawn in scale) with the link lengths L2 = a = 6 cm, L3 = b = 25 cm, L4 = c = 30 cm, L1 = d = 12 cm and θ2 = 450. For RP = 4 cm, θ3 = 87.80, θ4 = 103.10, δ3 = 450, ω2 = 10 rad/s, ω3 = -7.7 rad/s, ω4 = -5.2 rad/s and α2 = 10 rad/sec2, the angular acceleration of link 3, α3 is equal to
Q#03 :In a four-bar chain ABCD, Link AD is fixed and is 160 mm long. The crank AB is 40 mm long and rotates at 150+(23) r.p.m clockwise. While Link CD is 70mm long and oscillates about point D. BC and AD are of equal length, angle BAD=60°. Find the angular velocity of Link CD?
The large (1) wheel in figure 1 is rotating around the fixed axis passing through point O with an angular speed w1 = 4rad / sec. The OA crank rotates around the fixed axis from point O with an angular speed woa = 2rad / sec. Find the center of velocity P and angular velocity w2 of the small (2) impellers moving in a plane. Also, if (OK) = R = 60cm, (AB) = r = 20cm, (AC) = 12cm, (AE) = 11cm, (2) find the velocities of the A, B, C, E and K points of the impeller and form Table 3. . Also show the velocity vectors of the points A, B, C, E and K on the figure.
A 2.5 ft diameter flywheel of a gas engine has a pulley 10 in. in diameter bolted to it (both turning together). The flywheel turns at a speed of 150 rpm. Find a. the angular speed of the pulley in radians per second b. the linear speed in feet per minute of a point on the surface of the flywheel c. the linear speed in feet per minute of a belt running on the pulley, assuming no slipping between the belt and pulley surface.