(e) Assume a wireless communication system where the symbols -1 and 1are transmitted independently and with equal probability. In addition, assume that during their transmission, the symbols are affected by independently distributed additive noise with its pdf given in Figure 2. Figure 2 Calculate the mean the and variance of the additive noise of Figure 2.

(e) Assume a wireless communication system where the symbols -1 and 1are transmitted independently and with equal probability. In addition, assume that during their transmission, the symbols are affected by independently distributed additive noise with its pdf given in Figure 2. Figure 2 Calculate the mean the and variance of the additive noise of Figure 2.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Answer the following: (a) What is the maximum data rate for a 64-level system with an analog bandwidth of 400 MHz? (b) What is the maximum data rate if that same system is subject to noise, with an average power level of 600 and an average noise level of 200? Include units in your final answer.
2. Explain the following (a) sensitivity of a receiver (b) selectivity of a receiver. Why are these important characteristics? In what units are they usually expressed?
Q2. Explain how you would determine the primary and secondary constants of transmission by impedance measurements. Also, explain how the velocity of propagation and attenuation constant can be experimentally determined.
2. In voice morphing application of DSP a person voice is captured and sampled for 50second by using 24-bit ADC at a sampling frequency of 40 kHz. The samples arestored on a memory chip.i. What is the minimum memory size in bytes required to store all the samples?ii. How long the signal must be sampled to store the samples in 4 GB hard disc.iii. What should be the highest frequency component of the signal?iv. If the sampling frequency is increased by 25% then how long the signal mustbe sampled to store samples in 4 GB hard disc.
2. A singer voice is sampled for 4 second by an 8-bit ADC at a sampling frequency of 10 kHz. The samples are stored on a memory chip. i. What is the minimum memory size both in [bits and bytes] required to store all the samples? ii. How long the signal must be sampled to store the samples in 100Mbytes CD- ROM iii. What should be the highest frequency component of the signal? iv.If sampling frequency is doubled then how long the signal must be sampled to store samples in 100Mbytes CD-ROM
Type your question here Two resistors connected in series and at differing temperature are shown below. (a) Derive relations for the noise – equivalent resistor and temperature ???, ???. (b)Calculate ???, ??? for the specific case where: ?1 = 1?Ω , ?2 = 2?Ω , ?1 = 300 ?2 = 390 ?
Write short notes (max. three lines) on each of the following:(a) The effect of Quantization error on PCM signal spectrum and transmission rate.(b) The Transmitter Mixer.(c) Manchester codes (what/why/advantage(s)/disadvantage(s))
Communication system The question is : explain the occurrence of the white noise in the communication system. also drive the relationship for the transferred thermal noise voltage to a load of resistance R.
12 )Which is not the downside of analog signal processing? Difficulty keeping informationHigh sensitivity to electrical noiseLimited dynamic range in signal amplitudeRobustness against noiseRepeatability
Reduce the block diagram a) Reduce the block diagram b) Replace the values (c) Use the Routh-Hurwitz criterion to determine the stability of the system, is the system stable? is the system stable?
Describe the general process for “digitizing” audio and image data. Be certain to reference the relevant electronic circuits in your answer
NUMERICAL DATA COMMUNICATION An analog signal in sine form is intended to be transmitted to the receiver by pulse code modulation.Given below Define the parameters and answer the questions asked from you. *Peak to peak amplitude = xxx volts *Signal frequency = xxx Hz *Medium height form factor: xxx level 1-)What should be the theoretical minimum sampling frequency for the signal to be reconstructed in the receiver without distortion? 2-) What should be the practical minimum sampling frequency for the signal to be recreated in the receiver without distortion?