E R₂ C₁ Lo Consider the circuit shown in the figure. The battery voltage is = 22.00 Volts. The resistors have values of: R₁ =12 Ohm R₂ = 14 Ohm The capacitors have values of: C₁ =173 µFarad C₂ = 219 μFarad His 10-6 There is no charge on the capacitors before the switch is closed. C2 a) What is the charge on capacitor C₂ immediately after the switch is closed? 0 b) What is the current through R₂ immediately after the switch is closed? 0 c) What is the current through resistor R₁ immediately after the switch is closed? 1.83 d) What is the current through C₂ a long time after the switch is closed? R₂ e) What is the charge on capacitor C₂ a long time after the switch is closed? Amps Amps Coulomb Amps

E R₂ C₁ Lo Consider the circuit shown in the figure. The battery voltage is = 22.00 Volts. The resistors have values of: R₁ =12 Ohm R₂ = 14 Ohm The capacitors have values of: C₁ =173 µFarad C₂ = 219 μFarad His 10-6 There is no charge on the capacitors before the switch is closed. C2 a) What is the charge on capacitor C₂ immediately after the switch is closed? 0 b) What is the current through R₂ immediately after the switch is closed? 0 c) What is the current through resistor R₁ immediately after the switch is closed? 1.83 d) What is the current through C₂ a long time after the switch is closed? R₂ e) What is the charge on capacitor C₂ a long time after the switch is closed? Amps Amps Coulomb Amps

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 68AP: A circuit contains a D-cell battery, a switch, a 20- resistor, and three 20-mF capacitors. The...

See similar textbooks

Similar questions

Integrated Concepts A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg. °C, assuming no heat escapes?
Consider the circuit shown in the preceding problem. Write equations for the power supplied by the voltage sources and the power dissipated by the resistors in terms
(a) Explain how the mnemonic ELI the ICE man can be used to recall whether current leads voltage or voltage leads current in RLC circuits. Note that E represents emf . (b) Explain how CIVIL works as another mnemonic device, where V represents voltage.
In the circuit shown in Figure OQ21.15, each battery is delivering energy to the circuit by electrical transmission. All the resistors have equal resistance. (i) Rank the electric potentials at points a, b, c, d, and e from highest to lowest, noting any cases of equality in the ranking. (ii) Rank the magnitudes of the currents at the same points from greatest to least, noting any cases of equality.
Consider the circuit shown in Figure P28.21 on page 860. (a) Find the voltage across the 3.00-0 resistor, (b) Find the current in the 3.00-12 resistor.
Consider the circuit shown in Figure P18.10. (a) Calculate the equivalent resistance of the 10.0- and 5.00- resistors connected in parallel. (b) Using the result of part (a), calculate the combined resistance of the 10.0-, 5.00-, and 4.00- resistors. (c) Calculate the equivalent resistance of the combined resistance found in part (b) and the parallel 3.00- resistor. (d) Combine the equivalent resistance found in part (c) with the 2.00- resistor. (e) Calculate the total current in the circuit. (f) What is the voltage drop across the 2.00- resistor? (g) Subtracting the result of part (f) from the battery voltage, find the voltage across the 3.00- resistor. (h) Calculate the current in the 3.00- resistor. Figure P18.10
In Figure 21.41. does the graph indicate the time constant is shorter for discharging than for charging? Would you expect ionized gas to have low resistance? How would you adjust R to get a longer time between flashes? Would adjusting R affect the discharge time?
Construe! Your Own Problem Consider a rechargeable lithium cell that is to be used to power a camcorder. Construct a problem in which you calculate the internal resistance of the cell during normal operation. Also, calculate the minimum voltage output of a battery charger to be used to recharge your lithium cell. Among the things to be considered are the emf and useful terminal voltage of a lithium cell and the current it should be able to supply to a camcorder.
An electronic apparatus may have large capacitors at high voltage in the power supply section, presenting a shock hazard even when the apparatus is switched off. A “bleeder resistor" is therefore placed across such a capacitor, as shown schematically in Figure 21.50, to bleed the charge from it after the apparatus is off. Why must the bleeder resistance be much greater than the effective resistance of the rest of the circuit? How does this affect the time constant for discharging the capacitor?
A 50resistor is connected across the emf v(t)=(160V)sin(120t) . Write an expression for the current throug1 the resistor.
A 20.00-ohm; 5.00-watt resistor is placed in series with a power supply, (a) What is the maxim tun voltage that can be applied to the resistor without hanniug the resistor? (b) What would be the current through the resistor?
The- pair of capacitors in Figure P28.63 are fully charged by a 12.0-V battery. The battery is disconnected, and the switch is then closed. Alter 1.00 ms has elapsed, (a) how much charge remains 011 the 3.00-F capacitor? (b) How much charge remains on the 2.00-F capacitor? (c) What is the current in the resistor at this time?