Give me right solution with clear calculations. Problem 4: An A992 steel W305x87 is 7.5 m long and is pinned at both ends and braced in the weakdirection at the third point. Determine the available compressive strength.16PropertiesA,-10,965 mmtw9 mm 16 mml-197.71x10 mm1,-43.288x 10 mm305250

Answered: Image /qna-images/answer/06fa36e8-fe0a-424c-9fe2-12d4368ca5ef.jpg

Answered: e the available compressive strength.

Engineering

Civil Engineering

e the available compressive strength.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A W 360 x 44 of A992 steel column (Fy =345 MPa) having a length of 4m is fixed at both ends. Compute the effective width, be, of the slender web.Compute the value of reduction factor, Q, due to slender elementsin compression members.Compute the nominal compressive strength of the W-section.Properties of W 360 x 44Ag = 5710 mm2d = 351 mmbf = 171 mmtf = 9.78 mm tw = 6.86 mmkdes = 19.9 mmk1 = 19.1 mmrx = 146 mmry = 37.8 mm
Assume that the axial load P = 40kN applied to the lap joint is distributed equallyamong the three rivets. What is the smallest diameterof the rivetif the allowable stresses are 90 MPa for bearing between a plate and a rivet, and 40MPa for shear in rivets?
A W40x149 A36 steel girder spans 12 m on simple supports. It carries a uniformly distributed load of 75 kN/m over its entire length, and equal concentrated loads of 30 kN at quarter points of the span. (Ix = 4071x10⁶ mm⁴ ; Sx = 8390x10³ mm³ ; d = 970 mm; Aflange = 28,258 mm² ; Iy = 95x10⁶ mm⁴). Neglect the weight of the beam. a. Determine the width top and bottom reinforcing plates 14 mm thick if necessary.
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given: Determine the spacing, in mm, of rivets on the steel plate.
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. 2. Determine the moment of inertia, I, of the section in mm^4.
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. Determine the maximum flexural stress on the beam in MPa. Determine the maximum shearing stress on the beam in MPa.
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear Determine the location of centroid, y, from top of the beam in mm Determine the moment of inertia, I, of the section in mm^4. Determine the maximum allowable moment, M(all) in kn-m, base on the beam's cross-section. Determine the location of the maximum moment on the beam in meters. Determine the maximum moment, in kN-m, on the beam Determine the maximum flexural stress on the beam in MPa.
Taking into account only the effect of normal stresses, determine the strain energy ofthe prismatic beam AB for the loading shown. M0 (11kNm), L (3.4m), a (1cm), b (7cm) , d (14cm) , E (185GPa) , G (75GPa)
The singular force F will be applied to the kin with a hollow rectangular cross section. Accordingly, the location and value of the minimum normal stress that will occur in the whole beam is given correctly in the following? F-800 N. L1 - 4m, 12 - 1m, h1-48mm, h2 -72mm, b1-10mm, b2-20mm
Situation 1| An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Thickness, tf=9mm Flange Width, B=112.5 mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear 1. Determine the location of centroid, ȳ, from top of the beam in mm
A structural beam of the cross-section shown issubjected to a bending moment M = -7.5 kip.ftabout its Z-axis. Determine (a) the location of N.A.from the bottom of the section, (b) the moment ofinertia about N.A., (c) the section modulus for thetop and bottom utmost fibers, (d) the magnitudeand sign of the bending stress at point K, located3.32 in. above N.A., (e) the maximum tensilebending stress in the section, and (f) the maximumcompressive bending stress in the section.
A built-upsection is to be used as a girder. It is simply supported over a span of 9 meters and laterally supported at supports and midspan. Use Fy=345MPa and Cb=1.0 Properties of the section: A=12,620mm2 d=450 mm tw=10 mm bf=300mm tf=14mm rx=203.88mm ry=70.67 mm Ix=524.59x106mm4 a.Determine the elastic section modulus, Sx. b.Determine the plastic section modulus, Zx. c.Determine the compactness of the section. d.Determine the lateral support condition. e.Determine the Allowable Flexural Strength of the girder. f.Determine the Ultimate Flexural Strength of the girder.