Each cylinder of six cylinder internal combustion engine has a diameter of 60 mm and a stroke length of 400 mm. What is the engine capacity in litres? Give your answer to 2 decimal places.

Q: A hydraulic jack has a 2-inch diameter input piston and a 2-inch diameter output piston. If a 300 lb…

A:

Q: The top of a piston for a compressor has an area of 3.4 sq in. Find the areato the nearer thousandth…

A: Solution     1 sq in = 6.4516 square centimeter

Q: Find in inches the inside diameter of this water pipe for an automatic icemaker. Express the answer…

A: Given     Outside diameter, d = 1 1/4 in                                  = 1.25 in…

Q: C 3 ft

A: Writing the co-ordinates of different points – The position vector

Q: The height (in m)

A: Given data; A ball of mass 0.1 kg, initially at rest Ball dropped from height of 1 m.Ball impact…

Q: Calculate the magnitude

A: The provided force system is shown below.

Q: heres is in millimeters and v is in millimeters ne

A: Given data V= 13 S(9/8)  Required  Acceleration at school= 5 mm

Q: What is the weight of 12 kilogram object, expressed in lbf?

A: Given data Weight is 12 kg

Q: with respect to = 30° with the ientation of the a.

A:

Q: Engine piston weight 220 g. Machine speed 4700 rpm. What is the high acceleration of the piston when…

A: The weight of engine piston is given as, w=220 g. The machine speed of the engines is given as,…

Q: Determine the maximum diameter of a ball floating on water at 20°C if it has a density of 5060…

A: It is required to determine max diameter of ball

Q: Dimensions in millimeters forco (in N) of the V.component of the internal nin at D

A:

Q: In this system, the dimension of the part is allowed to vary on both the sides of the basic size

A: Given:

Q: Determine the mass of a steel ball whose diameter is 16mm.

A:

Q: A master cylinder has 150 pounds per square inch of pressure applied to the piston. The diameter of…

A:

Q: elocity at a point inside

A: given:x=20cm

Q: The mass of casting is 120kg after 6% of its mass was machined off. Determine the mass of the…

A: The mass of casting is 120kg after 6% of its mass was machined off. Determine the mass of the…

Q: The radioactive isotope of lead, Pb-209, decays at a rate proportional to the amount present at time…

A:

Q: The engine piston weighs 180 g. The machine speed is 4400 RPM. What is the maximum speed of the…

A:

Q: Use the following figure for both questions below. 1. The end of a tank containing water is vertical…

A: As per company policy, we are restricted to solve one question at a time. Please ask other question…

Q: Find the area of the following shape using the information provided.

A: Given Shape To find Area of the shape

Q: with his maximum velocity until he f three decimal places.

A:

Q: A hydraulic press is filled with oil with SG of 0.848. Neglecting the weight of the two pistons,…

A:

Q: Determine the total increase in length.

A: Given: E1=175 GPa E2=210 GPa P=55 kN To determine: Total increase in length

Q: How many kilograms of -5°C ice per minute will melt and evaporate to steam after adding a total of…

A:

Q: unit of a is

A: Given; Van der Walils equation of state is;  p±v-b=RT where,   p= pressure v= specific volume  T=…

Q: Find the x-component of F1 in Newtons. If the calculated answer is not whole number, express it in 4…

A: ****************************************

Q: A SHEROID HAS A FIRST ECCENTRICITY OF 0.81427. COMPUTE THE VALUE OF ITS FLATTENING.

A:

Q: A tank contains 500 kg of a liquid whose specific gravity is 2. Determine the volume of the liquid…

A: Given: m=500 Kg S=2

Q: dimension of the block (in mm) is

A: Given; σ=500ε0.1where,  ε true strain Young modulus= rl is 200 GPa Block thickness=100 mm material…

Q: The liter is defined as 1000 cubic centimeters. Convert 13 liter to gallon. o 3.432 gallon

A: Given data 1 liter = 1000 cubic centimetre 13 litres to gallon is

Q: Compute ly (I bar sub y, in mm“, round-off to 2 decimal places) for the region shown. 80 mm 20 mm 60…

A:

Q: building has the dimensions of 20 feet by 49 feet.   What is the area of the building in square…

A: Given dimension of the building Length = 49 ft Breadth = 20ft    To determine :the area of building…

Q: Find the area of the figure shown. a=3 cm b= 6 cm Take pie3D3.14 Round answer to one decimal place.…

A: It is required to determine area of given section

Q: In 30 force, if e is the angle between the positive xaxis and the piane contalining the force F, and…

A: Consider the diagram shown below for the force F.

Q: Find Ix for the shape below:

A: To determine: The moment of inertia of the shape about X axis. Image: Consider a image below:

Q: B-Determine the value of shaded area of the following figure.

A:

Q: Determine final dimension of the block in mm

A: Given data; Flow stress (in MPa) of a material is given by;                       =δ=500ε0.1  Young…

Q: ine the value of P.

A:

Q: How many balls of 50 mm diameter fit in a volume of 4.1 m^3

A:

Q: This composite shape is composed of a square, a half-circle, a triangle and a circular hole.…

A:

Q: Determine the Sommerfeld number

A: Given; A hydrodynamic journal bearing is subjected to,N=2000 rpmc=20×10-3μ=0.03 Ns/ m2W=2000 N

Q: 1. Determine the reading on the vernier scale as indicated by the arrows.

A: According to scale Main scale reading = 41 mm Least count = 1/20= 0.05 mm Vernier scale = 5*0.05=…

Q: A manometer with two tubes are connected to the roof of a car. The first tube points to the front of…

A: Answer: The speed of the car is 47.70 mph.

Q: The pressure 16 m below a certain liquid surface is 676.202 kPa. Which of the following most nearly…

A: Specific gravity of liquid is the ratio of liquid density and water density. Specific gravity don't…

Q: ment at midspan (in kip-ft to one decimal) for the following bear kip/ft, L = 26 ft, and a = 6 ft.…

A:

Q: compute for the value of T.

A: This can be treated as a simple Mechanics problem that can be solved either by Lami's theorem or by…

Q: Q6 Each cylinder of six cylinder internal combustion engine has a diameter of 60 mm and a stroke…

A:

Q: two blocks each weighing 1.5 kN

A: Find the mass of each block.