Electronics What is clocking block. If default skew is not given then when input signal sampled and output signal driven.
Q: 6. Describe the operation of an OTE instruction.
A: OTE : This is a instruction which is used in the PLC . PLC : Programmable Logic Controllers.
Q: a- Draw the circuit of 4-bits Johnson counter and draw its timing diagram
A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…
Q: 7). selector/multiplexer. Implement the logic function specified in Table by using a 74HC151 8-input…
A: The output can be obtained from the truth table and the same can be implemented by using 8x1…
Q: In a PCM system, if maximum frequency of the input analog signal is 5 KHz and number of levels in…
A:
Q: What is negative edge triggered?
A: The negative edge triggered means, the design changes its state only at the falling edge of the…
Q: A 9 bit asynchronous counter has a 128 - kHz clock signal applied. i) What the mod Number of this…
A: i) The given asynchronous counter is 9 bits. The mod number of the counter is given as: Mod…
Q: certain clocked FF has minimum ts = 20 ns and tH = 5 ns. How long must the control inputs be stable…
A: The explanation is as follows.
Q: Draw a block diagram of successive approximation ADC and explain its operation briefly.
A: Block diagram of successive approximation ADC
Q: Write a gate level verilog code for Multiplexer
A:
Q: Microprocessor 8085 : Note 1: Use F for fetch, R for memory read, W for memory write, IOR for IO…
A: In the 8085 Instruction set, SIM referred to as Set Interrupt Mask. 1-Byte instruction and also…
Q: What is the effect of instruction CMC? Set CF=1 Clear CF=0 If CF=1 Change to CF=0, and If CF=0…
A:
Q: 4 RESET is an 5- Address lines of 8086/8088 are (input, output) signal for the 8086/8088. type,…
A: Fill in the blanks for questions 4&5 ?
Q: 2. What is the duration of bus cycle in 8086 MPU if the clock is 20 MHz and two wait states are…
A: Actually all the questions are different, so I am solve 1St questions. 2.
Q: Define the analog and logic circuits. List the Logic Circuit advantages / disadvantages.
A: An analog circuit is a circuit which gives a continuous signal (continuous in both time and…
Q: Select all the 8088 input signals that can cause the microprocessor to take an interrupt. O INTR OSC…
A: The 8088 input signals that can cause the microprocessor to take an interrupt is INTR, INTA, and…
Q: the similarities between pic16F877A and 8051, the differences between timer for both Microcontroller…
A: We have given the following problem
Q: What is the maximum conversion time for a counting ADC using a 12-bit DAC and a 2-MHz clock…
A: Given data: fc=2 MHzn=12 bit The expression for the maximum conversion time is given as,…
Q: TTL output circuits are classified into two main kinds. What are these two sorts?
A: TTL output circuits classification
Q: A 9-bit asynchronous counter has a 128-kHz clock signal applied. (i) What is the MOD number of this…
A: Given here a 9-bit asynchronous counter has a 128-kHz clock signal and here we have to find the mod…
Q: Identify the type of signal processor element? a. Variable manipulation b. Variable controlling c.…
A:
Q: Design a synchronous clocked MOD-13 counter and show its timing diagram. Consider the positive edge…
A:
Q: How many bits are required to represent the Arduino analog input? Hint: There are 1024 possible…
A:
Q: (b) Briefly explain the key principle behind the Successive Approximation Convertor in how it goes…
A: Principle and working of SAR type ADC 1) SAR is one of the most widely used types of ADC. Here bits…
Q: Q9- Complete the following timing diagram for the circuit shown below. Assume a small delay for…
A: The D Flip-Flop circuit diagram is shown below, Here, all the inputs and signals are active high.
Q: In IC 74153,the input at pin number 14 is Options A-Connected to ground B-Connected to power/VCC…
A: IC 74153 has two 4-by-1 multiplexers in it. A multiplexer has four inputs for input data, 2 lines…
Q: (i) The value of positional error constant is : (ii) The value of velocity error constant is : The…
A:
Q: Explanation about (Deal with operational amplifier controllers and programmable logic controllers)
A:
Q: Explain how a priority encoder works
A: A priority encoder is a circuit or method that reduces the number of outputs from numerous binary…
Q: [0 5] the signal in the volt range will be quantified. since n=4; a)Calculate what is the number of…
A: We need to calculate number of level , and step size for quantization .
Q: A 16-bit successive approximation ADC is to be designed to operate at 50,000 conversions/second.…
A: Given Nmax=50,000 conversion/s Calculating conversion time TT=1NmaxTT=150,000 conversion/sTT=2×10-5…
Q: ii) Draw the block diagram of the ACC system. What is the refer- ence signal, what is the control…
A:
Q: Which module of the microcontroller will definitely be used if an analog signal needs to be read in…
A:
Q: Define terms upper and lower tripping points of Schmitt trigger. What is the significance of 3…
A: Given A Schmitt trigger circuit.We need to define UTP and LTP of a Schmitt trigger circuit Nd its…
Q: Q:what is the addressing mode for the following instruction: MOV .(C910), A direct mode Relative…
A:
Q: Complete the table and timing diagram (Q0,Q1,02,0Q3) for the 4-stage synchronous binary counter…
A:
Q: frst second 1 00 AA' third 110
A: ASM chart there are three components. They are i) state box, ii) Decision box, iii) condition box.…
Q: Discuss: Include how the output voltage is produced in LDR, then how the ouput voltage is produced…
A: Include how the output voltage is produced in LDR, then how the output voltage is produced in 555…
Q: How many flags are implemented in 8085 microprocessor?
A: In 8085 microprocessor, the flags register can have a total of eight flags. Thus a flag can be…
Q: What is the reset vector of the 8088 microprocessor? Explain how it is used to begin operation.
A: The reset vector of a microprocessor is the default location where the processor will go to find the…
Q: Q.19 Draw logic diagram for 4 to 1 line multiplexer. Q.20 Draw logic diagram for 1 to 4 line…
A: Solution: Logic diagram of the 4×1 multiplexer is given as follows: Where,…
Q: A system with motor is using an absolute position encoder with the last reading of 10011011. If it…
A: According to the question,
Q: one method of eliminating contact bounce wherein it triggers on the first contact bounce instead of…
A: To select proper answers from options.
Q: For the ALU circuit shown below, what should be the control word (S251SO) to perform the (sl A)…
A: According to the question, for the given circuit as shown below We need to find the condition for…
Q: a) Asynchronous Inputs b) Edge triggered c) Shift register d) State transition diagram e) Parallel…
A: a) Asynchronous Inputs - In asynchronous inputs, the signals which are input to the flip-flops are…
Q: What is the use of stack in micro-processor 8086?
A: Stack - It behave as first in last outIt is a temporary data storage memory . Stack contain four…
Step by step
Solved in 2 steps
- A 16-bit successive approximation ADC is to be designed to operate at 50,000 conversions/second. What is the clock frequency? How rapidly mustthe unknown and reference voltage switches change state if the switch timing delay is to be equivalent to less than 0.1 LSB time?2.Assuming the processor frequency is 20 MHz, find the highest square wave frequency that can be generated using Timer0 in 16-bit mode. (Calculations only, no code needed).A 9 bit asynchronous counter has a 128 - kHz clock signal applied. i) What the mod Number of this counter ? ii) What will be the frequency at the MSB output ? iii) Assume that the counter starts at zero.What will be the count after 6.15 input pulse?
- The 8085-instruction set does not include a Clear Carry instruction. Which single-byte logical instruction can clear the carry without modifying the contents of the accumulator?Microprocessor 8085 : Note 1: Use F for fetch, R for memory read, W for memory write, IOR for IO read, and IOW for IO writeNote 2: Use hexadecimal where possible Q/ Using (SIM) instruction, what is the data required in the accumulator to enable all hardware interrupts and send a (zero) serially?Implement Four-to-one-line multiplexer with Logic diagram and Function table.
- The 8085 instruction set does not include a Clear Accumulator instruction. Which single-byte logical instruction can perform this task?What is the mathematical model for binary amplitude shift keying?A frequency counter is gated on for 10 ms and counts 540 pulses from a periodic input signal . What is the input frequency? a) If the gate time is changed to 100 ms , approximately how many counts would you expect from the same source during the gate time? b) In what way does the change in the gate time affect the resolution?