em 4: Two masses of 14 kg and 7 kg connected by a flexible inexténsible cord rest on inclined plane shown below. When the masses are released what will be the tension T in the cord? Assume the coefficient of friction between the plane and the 14 kg mass is 0.25 and between the plane and 7 kg mass is 0.375.

em 4: Two masses of 14 kg and 7 kg connected by a flexible inexténsible cord rest on inclined plane shown below. When the masses are released what will be the tension T in the cord? Assume the coefficient of friction between the plane and the 14 kg mass is 0.25 and between the plane and 7 kg mass is 0.375.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.77P: The cone clutch transmits the torque C through a conical friction surface with cone angle . The...

See similar textbooks

Similar questions

Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The cone clutch transmits the torque C through a conical friction surface with cone angle . The inner and outer radii of the friction surface are a and b, respectively. The left half of the clutch is keyed to the shaft, and the right half drives a machine (not shown) through a gear attached to its outer rim. Assuming uniform pressure on the friction surface, show that the maximum torque that can be transmitted by the clutch is
The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
PROBLEM: To prevent a box from sliding down an inclined plane, student A pushes on the box in the direction parallel to the incline, just hard enough to hold the box stationary. In an identical situation, student B pushes on the box horizontally. If the weight of the box w= 20.0 N, the angle made by the incline with the horizontal θ=25o, and the coefficient of static friction µs=0.16, who has the easier job?
In a porter governor the mass of the central load is 18 kgand the mass of each ball is 2kg. the top arms (254) mm while the bottom arms are (304) mm long. The friction of the sleeve is 20 N. If the top arms make 45 deg with the axis of rotation in the equilibrium position, find the range of the speed of the governor in that position
A box of mass m = 30 kg is at rest on a ramp inclinedat 50° to the horizontal. The coefficients of friction between the box and the ramp are mS = 0.80 and mK = 0.70. Determine the magnitude of the largest force that can be applied upward, parallel to the ramp, if the box is to remain at rest.
A centrifugal clutch has four shoes, each of mass 0·35 kg. When at rest, the radialclearance between the shoes and the clutch drum is 15 mm and the radius to the centre ofgravity of the shoes is 225 mm. The shoes are held on retaining springs of stiffness 10kN/m and the internal diameter of the clutch drum is 600 mm. The coefficient of frictionbetween the drum and the shoes is 0·3.Determine:(a) The speed (in rev/min) at which the clutch starts to engage. For a rotational speed of 1200 rev/min:(b) The force each shoe exerts on the drum. (c) The torque transmitted. (d) The power transmitted.
A 6-m long ladder has a mass of 16 kg, and its center of gravity is 2.4 m from the bottom along the ladder. The ladder is resting on a 5° upward sloping floor at A and on a wall inclined to the right at 5° from the vertical at B, so that it makes an angle of 60° with the horizontal.How far up along the ladder can a 79-kg man climb before the ladder is on the verge of slipping? The angle of friction at all contact surfaces is 15°. Also determine the total reaction at A and B in Newton. Note: Point A is at the left of point B.
A cube with mass of m=80N is on the inclined plane with angle of phi=20 degrees. coeficient of static friction /mu_s = 0.25 coeficient of dynamic friction /mu_k = 0.15 Determine: what is the smallest size of the force F parallel to the inclined plane, which prevents the cube in the slide? what is the smallest size of the force F, which the cube starts to move along the inclined plane up? At what value of the force F starts the cube to rise at a constant speed?
A 8.0 m long ladder AB leans against a smooth wall making an angle of 70º with the floor. The ladder is uniform and has a mass of 40.0 kg.(a) Determine the forces exerted on the ladder by the floor and the wall (i.e. at A and B respectively).(b) Determine the minimum value of the coefficient of static friction to prevent the ladder from slipping.
A 6-m long ladder has a mass of 10 kg, and its center of gravity is 2.4 m from the bottom along the ladder. The ladder is resting on a 5° upward sloping floor at A and on a wall inclined to the right at 5° from the vertical at B, so that it makes an angle of 60° with the horizontal. How far up along the ladder can a 78-kg man climb before the ladder is on the verge of slipping? The angle of friction at all contact surfaces is 15°. Also determine the total reaction at A and B in Newton. Note: Point A is at the left of point B. SOLVE ASAP