Introductory Problems 6/1 The 85-lb force P is applied to the 200-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the crate. Ans. F = 85 lb to the left %3D 200 lb P = 85 lb H = 0.50 H = 0.40 %3D

Introductory Problems 6/1 The 85-lb force P is applied to the 200-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the crate. Ans. F = 85 lb to the left %3D 200 lb P = 85 lb H = 0.50 H = 0.40 %3D

Name: Introductory Problems6/1 The 85-lb force P is applied to the 200-lb c
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Introductory Problems6/1 The 85-lb force P is applied to the 200-lb crate, whichis stationary before the force is applied. Determine themagnitude and direction of the friction force F exertedby the horizontal surface on the crate.Ans. F=85 lb to the

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.19P: The 3600-lb car with rear Wheel drive is attempting to tow the 4500-lb crate. The center of gravity...

See similar textbooks

Similar questions

The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The brake pads at C and D are pressed against the cylinder by the spring BF. The coefficient of static friction between each pad and the cylinder is 0.15. Find the smallest tension in the spring that would prevent the cylinder from rotating when the clockwise couple M=2200lbin. is applied. Neglect the weights of the members.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
Calculate the force P that is required to hold the 120-lb roller at rest on the rough incline.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
The mass of the unbalanced disk is m, and its center of gravity is located at G. If the coefficient of static friction is 0.2 between the cylinder and the inclined surface, determine whether the cylinder can be at rest in the position shown. Note that the string AB is parallel to the incline.
The 3600-lb car with rear Wheel drive is attempting to tow the 4500-lb crate. The center of gravity of the car is at G, and the coefficients of static friction are 0.6 at B and 0.2 at C. Determine if the crate will slide.
The screw of the carjack has a pitch of 0.1 in. and a mean radius of 0.175 in. Note that the ends of the screw are threaded in opposite directions (right- and left-handed threads). The coefficient of static friction between the threads is 0.08. Calculate the torque C0 that must be applied to the screw in order to start the 1200-1b load moving (a) upward; and (b) downward.
Problem 4. A.) If the uniform concrete block has a mass of 500 kg, determine the smallest horizontal force P needed to movethe wedge to the left. The coefficient of static friction between the wedge and the concrete and the wedge and the floor is 0.3. The coefficient of static friction between the concrete and floor is 0.5.ANSWER: P=1797.52; N=1.80kNB.)Refer to problem number 4. Calculate the followinga.) the angle of friction between the wedge and the concrete and the wedge and the floor.Answer: ?????? ??? ????????= ?????? ??? ?????= 16.7ob.) the coefficient of static friction between the concrete and floor.Answer: ????????? ??? ?????= 263.56o