emts 8₁ = 19.9 V. 8₂-10.7 V, and 83-5.40 V, and the resistances are each 2.000. What are the (a) size and (b) direction (left or right) of current it? (c) Does battery 1 supply or absorb energy, and (d) what is its power? (e) Does battery 2 supply or absorb energy, and (f) what is its power? (g) Does battery 3 supply or absorb energy, and (h) what is its power? www €18,3 www ww www 4F =t&

emts 8₁ = 19.9 V. 8₂-10.7 V, and 83-5.40 V, and the resistances are each 2.000. What are the (a) size and (b) direction (left or right) of current it? (c) Does battery 1 supply or absorb energy, and (d) what is its power? (e) Does battery 2 supply or absorb energy, and (f) what is its power? (g) Does battery 3 supply or absorb energy, and (h) what is its power? www €18,3 www ww www 4F =t&

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter19: Special-purpose Outlets-water Pump, Water Heater

Section19.2: Water Heater Branch Circuit

Problem 8R: For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature...

See similar textbooks

Similar questions

You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
A solid specimen of dielectric dielectric constant of 4.0, shown in the figure has an internal void of thickness 1mm. The specimen is 1cm thick and is subjected to a voltage of 80 kV(rms). If the void is filled with air and if the breakdown strength of air can be taken as 30 kV(peak)/cm, find the voltage at which an internal discharge
a.) determine the type of system ( over damped, under damped, undamped, or critically damped ). b.) determine the value of the inductance L in H. c.) determine the value of the resistance R in Ω.
A battery of emf 30.0 V is connected to a switch, an inductor of inductance ? = 0.600 ? and two resistors, R1 = 10.0 ? and R2 = 6.00?. The switch is initially open. A. What are the values of currents ?1, ?2, ?3 just after the switch is closed? (Just give an answer) ?1 = ?2 = ?3 = B.)Which point, a or b, is at higher potential or are they at the same potential, just after switch S is closed? (Just give an answer) C. What is the value of current ?1 through the battery a long time after the switch is closed? Show your work and briefly explain your logic
Field current If can be varied by varying the resistance of field resistance which is connected in series with the field circuit. Select one: True False
Vbatt=25 VC1=90 ?CC2=75 ?CC3=60 ?CR1=160 ΩR2=120 Ωt2=21.6 msect3=27 msecConsider the circuit shown below which shows a battery connected to some resistors and capacitors along with some switches which will be toggled opened or closed at different times. The components are listed above. The capacitances are in microFarads (?F), the resitances are in Ohms (Ω), and the times are in milliseconds (msec). A stopwatch is started at time t1=0 ms. At that time, switch S1 is closed and all other switches are open and the capacitor is allowed to charge up.(a). (i)What is the charge (in uC) on C1 at the time the stopwatch reads t2=21.6 ms?a)3690 b)1520 c)5710 d)2630 e)683 f)1750 (a).(ii)What is the current (in mA) through R1 at t2=21.6 ms?34.9 30.4 114 13.6 73.6 52.4 (b)(i)What is the voltage (in V) across R1 at t2=21.6 ms?8.37 5.58 2.18 11.8 18.2 4.85(ii). What is the voltage (in V) across C1 at t2=21.6 ms?63.2 29.1 40.9 7.57 19.4 16.9(c). (i) What is the energy (in mJ) in C1 at t2=21.6 ms?6.63…
Q-1: Give brief answer to the following: (Answer Ten only)1) what is the potential transformer used for in power substation?2) what is process leads to lowering the number of free electrons?3) what is The Townsend’s Criterion4) why Sulphur Hexafluorid has good insulation strength?5) What is Intrinsic Breakdown6) why do bubbles lead to breakdown of liquid?7) how to decease the ripple voltage of cockroft-walton voltage multiplier circuit8) how much the maximum charging current of A Van de Graaff generator has a beltwidth 1 m, a belt speed of 4 m/s, and charge density of 10 c/m29) Why does need for Reactive Power Compensation in test transformer?10) The output voltage of series resonant circuit is given by the formula _________11) what is impulse voltage and what is its standard wave shape?12) Which advice can measure impulse voltage?
Directions : USE VDT and CDT IF POSSIBLE and solve the following1. In the circuit shown in Figure, the total charge is 750 μC. Determine thevalues of V1, V and C2.
Solar panels on one of the NWU solar car prototype, have an emissivity of e = 0.655. When in direct sunlight, they absorb energy at a rate of 796 J/s per square meter of surface. Assume that the only energy loss is due to the emission of radiation. What equilibrium temperature are the panels reaching?
Discuss briefly the importance of renewable energy.
The specific capacitance in F/g can be estimated by using both cyclic voltammetry curves atdifferent voltage scan rate and Galvanostatic charge-discharge curves. The following graphshows the charge-discharge curves of a typical MnO2 pseudocapacitive electrode. There is acharge drop in the voltage at the onset of the discharge curve (one such drop is denoted bydeltaV2). What is the reason behind it?
Write the solution