ERE IS A LEAK IN A HORIZONTAL 300 MM DIAMETER PIPELINE. UPSTREAM FROM THE LEAK TWO GAGES 600 METER APART SHOWED A DIFFERENCE OF 140 ???. DOWNSTREAM FROM THE LEAK TWO GAGES 600 METER APART SHOWED A DIFFERENCE OF 126 ??? . ASSUMING ? = 0.025. HOW MUCH WATER IS BEING LOST FROM THE PIPE. show answer in litre pe

ERE IS A LEAK IN A HORIZONTAL 300 MM DIAMETER PIPELINE. UPSTREAM FROM THE LEAK TWO GAGES 600 METER APART SHOWED A DIFFERENCE OF 140 ???. DOWNSTREAM FROM THE LEAK TWO GAGES 600 METER APART SHOWED A DIFFERENCE OF 126 ??? . ASSUMING ? = 0.025. HOW MUCH WATER IS BEING LOST FROM THE PIPE. show answer in litre pe

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.14P

See similar textbooks

Similar questions

A 200 mmФ pipeline whose length and friction factor (f) are 2.5 km and 0.018 respectively connects two tanks A and B. Assuming minor loss to be 10% of friction loss, and reservoir A 15 m higher than B, find the rate of flow * a. 0.03426 m³/s b. 0.05426 m³/s c. 0.04426 m³/s d. 0.06426 m³/s
A concrete dam and the flow net are shown in the Figure below. The following parameter are-5 3 given as: Nd=12, Nf=3.8, k=2.6X10 m/sec, and Ɣsat=19.5 kN/m .a) Calculate the total quantity of water lost by seepage in m3/day.b) What is the water quantity for each flow channel?c) What is the reading of pizometer if its location 1.5 m above datum?d) What is the factor of safety against piping at the down stream?
Water flows in a 350mm- diameter pipe at the rate of 600 liters per second. The pipe has a length of 64m. Compute the head loss using Darcy Weisbach formula with f=0.028. Compute the head loss using Hazen William’s Formula with C=92. Compute the head loss using Manning’s formula with n=0.012
An orifice on the side of a tank discharges water under a head of 9 ft. if the diameter of the orifice is 2”, the coefficient of contraction is 0.63, and the head lost is 0.80 ft, determine the discharge, CV and CD. Pls show also the figure/diagram
A parallel pipe net work connects the bottom of two reserviors. The head difference between the reserviors is 20 m. All three pipes have a ks value of 0.052. The lengths of the pipes are 70, 65 and 100 m and the diameters are 0.4, 0.35 and 0.5 m, respectively. Determine the velocity in each of the three pipes.
A 600 mm diameter horizontal pipe with a length of 1500m and C=120. the pressure gage attached downstream of the pipe reads 16kpa and another gage is attached upstream of the pipe reads 30kPa. If another gage is attached between the ends of the pipe. What is the total head loss?
1. A pipe has a slope of 1 in 100 and its length is 300 meters. Its diameter is 0.6 meter at the lower end while 1.2 meters at the higher end. The rate of flow through pipe is 5400 liters/min. Find the pressure at the lower end if the pressure at higher end is 68.07 kPa. Neglect losses.
Oil (SG = 0.89), with a kinematic viscosity of 0.007 ft2/s, flows in a 3-in.-diameter pipe at 0.049 ft3/s. Determine the head loss per unit length of this flow.
Write legibly Complex Pipeline System_Parallel Pipes 1. The pressure heads at junctions A and E are 70.0 m and 46.0 m, respectively, in the given parallelpipe system shown in the figure. Theflow rate of water entering junction A is 0.30 cms. Assuming that the Hazen – Williams roughness coefficient C = 120 for all pipes, determine the flow rate through each branch of the loop. For the solution, use the Hazen – Williams formula. Answer: a. Pipe ABE = _______________________ cmsb. Pipe ACE = _______________________ cmsc. Pipe ADE = _______________________ cms
High velocity water flows up an inclined plane, as shown in Figure 5 .1 What are the two possible depth of flow at section 2? Neglect al losses.
A confined aquifer with T = 7.0 x 10-3 m2/s and S = 5 x 10-4 is pumped by two wells, 35 m apart. One well is pumped at 7.6 L/s and one at 15.2 L/s. Plot the drawdown h0-h versus distance along a line joining the wells, 4 hours after the start of pumping. Use 5 m increments along the line. How would I go about this question if my initial r1 would equal 0 and and r2 would equal 35m additionally how would I get the pumping rates at each 5 m increments. overall please give a step by step on how I Would go about this question
With an observation well situated is 69.7 ft away from the pumping well (which is pumping at the rate of 305 gal/min). The aquifer is confined, and the depth has been measured from well logs and is 150 ft. please show using this data how to calculate transmissivity (T), the hydraulic conductivity (K) and Storativity (S) for the aquifer. Thank You s (m) t (sec) 20.7 4074.3 30.76 6054.6 46.3 9054.6 67.33 13254.6 107.26 21114 152.67 30054 209.37 41274 305.38 60114 451.68 88914 671.44 132174 946.07 186234 1321.9 260214