5... Estimate the evaporative loss of waterfrom a reservoir where surfacetemperature, as well as the ambientair temperature, is 40°C due during anunusual, dry heat wave period. Theair blowing over the reservoir leads toa surface mass transfer coefficient of0.25 m/s. Assume the water surface issaturated with water vapor, that theair is very dry (RH=0%!) beforecontact with water.

Given :- Water surface temperature T = 40 °C = 313 K surface mass exchange coefficient for blowing…

Answered: Estimate the ev from a reservoi…

Engineering

Civil Engineering

Estimate the ev from a reservoi temperature, as рerati air temperature

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter11: Temperature And Temperature- Related Variables In Engineering

Section: Chapter Questions

Problem 10P: Calculate the thermal resistance due to convection for the following situations: a. warm water with...

See similar textbooks

Related questions

Q: When an unconfined compression test was conducted on a cylindrical soil sample, it failed under an…

Q: /sec 1) Water is plowing at the rate of 3 A t E as shown in the piqure. Compute from. the pw in each…

Q: -12"- h = 9" #9 @ 5" o.c. clear - 12" Typical Section 19

A: Given data for slab breadth = 12 in = 12 in12 in= 1 ft height = 9 in = 9 in12 in = 0.75 ft dia of…

Q: Calculate straight line equation for following Transportation data Road Length, X (km) Number of…

A: Given table is about the road length in Km and number of vehicles on that span of road

Q: EXERCISES 2-18. Determine the reactions on the beam. The support at B can be assumed to be a roller.…

A: Draw free body diagram Hinged have two restrained Roller have one restrained Equilibrium…

Q: A horizontal water jet with a velocity of 10 m/s and cross-sectional area of 10 mm2 strikes a flat…

A: given-velocity v=10m/sarea A=10mm2density ρ=1000 kg/m3

Q: Please help me answer this. Thank you!! The steel framework is used to support the reinforced stone…

Q: A beam is subjected to equal bending moments of M, = 4300 N-m. The cross-sectional dimensions are b…

Q: Glycerine (SG = 1.26) flows through a pipe AB 48" in diameter at 10 fps and then passes through a…

Q: The axial load 210 kN applied to the lap joint is distributed equally among the three 16.5-mm-…

Q: Determine the value of EIv (in lb ft3 )at midspan for the beam loaded by two concentrated forces if…

Q: 3. What is the value of the reaction r1 in kN?

Q: PROBLEM 01: A hollow cylinder 0.80m in diameter and 1.2m long weighs 250kg. lead d=1m d=1m lead…

A: Hollow cylinder The volume of a hollow cylinder is the three-dimensional space it encloses. For…

Q: A beam is subjected to equal bending moments of M, = 3000 N-m. The cross-sectional dimensions are b…

A: Given : Applied bending moment, Mz = 3000 N-mCross-sectional dimensions are : b = 190 mm, c = 30 mm,…

Q: First problem: Simply supported beam loaded with concentrated loads. Second problem: Cantilever beam…

A: As per bartleby guidelines i am solving top three question if you want of solution of other question…

Q: Find: Using the Principle of Virtual Work, and with equations for internal bending moment for both…

Q: A plastic beam has a cross section with dimensions of a = 3.8 in., b = 13.3 in., d = 7.6 in., and t…

Q: PROBLEM 01: Given the figure below, (a) determine the value of h in the siphon shown if velocity at…

A: step 1-

Q: )

Q: In item No. I what is the value of phi (Φ)?

A: To find angle phi

Q: samples. Determine the MPN/100 mL using (a) the Poisson distribu- tion [Eq. (2.90)], (b) the MPN…

A: Most probable number (MPN) = It is a method to analyze the numbers of bacteria in a sample of water.

Q: 150. kN.m 25. kV/m C B 1m Im 4m R1 R2 FIGURE B

Q: What is the applied load P?

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 680 mm.…

A: ASKED: To determine the largest moment M that can be applied to the beam corresponding to the…

Q: Example: Find the discharge through a valve whose outlet diameter is 2m if the pressure just…

Q: A beam is subjected to equal bending moments of Mz = 3400 N-m. The cross-sectional dimensions are b…

Q: %3D What is the general solution of the differential equation y +4y = tan 2x? O y = C cos 2a +C sin…

Q: Constant head permeability tests were PENUI height of the two specimens (Ls1: Ls2) is 1.5, the ratio…

Q: 2-34. Determine the components of reaction at the supports. Joint Cis a rigid connection. 8 kN 6 KN…

Q: Please provide the complete UNITS ANALYSIS, USE OF CORRECT CONVERSION RATIOS and DIAGRAMS in your…

Q: s fo

Q: 2-29. Determine the reactions at the supports A. B, C, and D.

Q: A sand layer found at sea floor under 20 m water déptri is characterized with relative density =…

Q: Three soil specimens (Soil 1, and Soil 3), each 150 mm long and 100 mm diameter are placed in series…

Q: Q1 In a technologically advanced era, geographic information has a key component in solving global…

Q: A sand cone test has been performed in a compacted fill performed on a soil sample. The test results…

A: Sand cone test The sand cone test is a compaction test used in the field to determine the density…

Q: A simply supported beam with given loads is shown below. a) Which of the following gives the…

Q: For the given beam below bent about the horizontal axis of its cross section. Solve for fatMAX &…

Q: What is the value of the reaction at the right support in kN?

Q: 13. Which one is not a key aspect of IRS? Everyone must have a sincere wish to prevent accidents and…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: 1. Two tangents intersect at an angle of 42° are to be connected by a intersection to the point of…

Q: W18 × 40 standard steel shape is used to support the loads shown on the beam. Assume P = 30 kips, w…

Q: A river 5m deep consists of a sand bed with saturated unit weight of 20 kN/m³, Yw = 9.81 kN/m³. The…

Q: Determine the stiffness matrix and load vector for the following Frame Structure. P ton Lm K=EI P…

Q: The following data are given for a stream of uniform flow: average stream cross section =9.45 sqm ;…

Q: A two-storey school (use classroom) has interior columns that are spaced in 4.5 meters apart in two…

Q: A constant-head permeability test was conducted on a soil specimen under a hydraulic gradient of…

Q: Problem#3: A soldier holds a gun with the mass of 4.0kg by his arm and shoulder. Calculate the…

A: Given data: Combined mass of gun and arm-shoulder, M=4 +12.5=16.5 kg m=0.045 kg v=400 m/s

Q: 2. Another reinforced concrete beam has the following properties: • fy= 60 ksi • f= 5,000 psi • As =…

Q: \ beam is subjected to equal bending moments of M, = 3600 N-m. The cross-sectional dimensions are b=…

Concept explainers

Pressure and Stress

Question

5...

Estimate the evaporative loss of water
from a reservoir where surface
temperature, as well as the ambient
air temperature, is 40°C due during an
unusual, dry heat wave period. The
air blowing over the reservoir leads to
a surface mass transfer coefficient of
0.25 m/s. Assume the water surface is
saturated with water vapor, that the
air is very dry (RH=0%!) before
contact with water.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the evaporation using Combination Method (mm/day) from an open water surface with air temperature 22°C, relative humidity is 40% and wind speed is 3 m/s, all measured at height 2 m above the water surface. Assume a roughness height of 0.03 cm. The net radiation is 200 W/m^2. Cp=1005 J/kg-K *Kelvin = Degree Celsius + 273.2 , use this in computing for the density of air
1. In undisturbed air stream, where the pressure is 14.7 psi and density is 101325Pa, where the velocity is 500 ft/sec. What are the density, temperature, speed of sound, and specific weight where the velocity is 590ft/sec? g=9.8066 m/s^2
Calculate the thermal resistance due to convection for the following situations: a. warm water with h = 200 W/m2 K b. warm air with h = 10 W/m2 K c. warm moving air (windy situation) h = 30 W/m2 K
Estimate the outflow from a 2500 hectare lake in 20 days during which the lake level dropped by 105cm, an average inflow into the lake 5x10^5 m^3/day.During 20 days, the seepage loss from the lake was 5.5cm,total precipitation on the lake was 0.25m while the total evaporation was 15mm. Give final answer in m^3/s.
A lake with a surface area of 275 ha has the values of: relative humidity = 60% wind velocity at 1m above the ground = 10 kph mean barometric reading = 750 mmHg es = 30 mmHg Km = 0.36 Estimate the average daily evaporation from the reservoir and the volume of water evaporated in the body in 5 days using ROHWERS
Find the wind speed needed (in miles/hour) to obtain a daily evaporation of 0.163 in/day, if the air temperature was 80 degrees F, and the relative humidity was 25%.
9. Water is flowing in a rectangular flume with a velocity of 3.81 m/s and a depth of 0.98m. (a) is the flow at the upper or lower stage? (b) Compute the specific energy. (c) What is the alternate depth of flow with equal energy?
Compute the evaporation rate from a lake for June if the average water temperature is 80°F, measured 1 foot below the surface of the lake, and a monthly average wind speed of 6.7 mi/hr, measured at 25 feet above the lake. The average air temperature for June is 74°F and the average for June is 71%.
compute evaporation rate in milliliters per day using "aerodynamic method"
Determine the lake evaporation for a month in which the average water temperature is 22.5 degree celsius and average wind speed at 10m is 14.5 kph at a relative humidity of 40 percent. Subject: Hydrolody
WATER RESOURCES ENGINEERING: Evaporation The temperature and relative humidity values for the month of October are: Mean air temperature at 4 m = 18o C Maximum lake temperature = 13.5o C Maximum pan temperature = 15o C Relative humidity = 35% Determine the monthly evaporation from the lake (in cm) using the Energy Balance Method. The average net radiation is 90 W/m2. Disregard sensible and ground heat fluxes.
At 68 ˚F water has a dynamic viscosity of about 2.11 x 10 -5lb-s / ft2, solve the kinematic viscosity (in ft2/s) of water whose specific gravity is 0.998. Note ?????? =62.4 ??/??3 at normal condition.