EX: The uniformly distributed vertical load on the rectangular area is q1 =100 kN/m², and the uniformly distributed vertical load on the semicircular area is q2 = 200 kN/m². Determine the vertical stress increase due to the loaded area located at a depth of 3 m below points A and B. 3 m 4 = 100 kN/m² 4= 200 kN/m² A 2 m 1m 2 m B 3 m 41

EX: The uniformly distributed vertical load on the rectangular area is q1 =100 kN/m², and the uniformly distributed vertical load on the semicircular area is q2 = 200 kN/m². Determine the vertical stress increase due to the loaded area located at a depth of 3 m below points A and B. 3 m 4 = 100 kN/m² 4= 200 kN/m² A 2 m 1m 2 m B 3 m 41

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.11P

See similar textbooks

Similar questions

The soil profile at a site is shown Figure P16.3. Find the total horizontal normal stresses at A and B, assuming at-rest conditions.
Repeat Problem 10.12 for q = 700 kN/m2, B = 8 m, and z = 4 m. In this case, point A is located below the centerline under the strip load. 10.12 Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft. Determine the increase in vertical stress at point A located z = 21 ft below the surface. Given x = 28.8 ft. Figure 10.43
A strip load of q =53 kN/m^3 is applied over a width B =11m. Determine the increase in vertical stress in kPa at point A located z = 4.6 m below the surface. x = 8.2m
A flexible rectangular area 3m by 2m is subjected to a uniformly distributed load of q = 200 kN/m2. Determine the increase in vertical stress at the center at a depth of z = 3 m.
A 5-m-diameter tank supported on the surface of a soil deposit imposes a bearing pressure of 225 kPa (225 kN/m2). For a point 4 m below the tank base, compare the vertical stress increase due to the tank loading when:(a) the Westergaard conditions are assumed.(b) the 60° approximation is assumed.
The plan of a flexible circular loaded area is resisting the uniformly distributed load(q), 835 kN/m2 with the radius of 5.7 m. Illustrate and calculate the increase in thevertical stress (Δσ) at a depth of z = 7.2 m below point A which is immediately belowthe center.
A steel storage tank 20 m in diameter will be used to hold a liquid petroleum product. When filled, the tank causes a bearing pressure of 150 kPa. The soil underlying the tank has a unit weight of 18.5 kN/m3. For a depth 10 m below the base of the tank, compute the effective vertical stress when the tank is empty and when full, for points beneath the center and beneath the edge.(a) Assume the Boussinesq conditions apply.(b) Assume the Westergaard conditions apply.
A level ground surface exists in an area where soil in the underlying stratum has a wet unit weight of 19 kN/m3. The vertical pressure at any depth represents the major principal stress. The vertical pressure (stress) is the product of the soil unit weight and depth. The lateral pressure at a corresponding depth is 0.45 times the vertical pressure and represents the minor principal stress. (a) Determine the principal stresses acting at a depth 4 m below the surface, and draw the Mohr’s circle for the condition. (b) What is the maximum shear stress acting at this depth?
Referring in the Fig. 2 below, B = 6m and q =150 kPa. For Point P, z = 2m and x = 1.5m. Determine the vertical stress at Point P.
A flexible circular area of radius 3.3 m. is uniformly loaded by q = 315 kN/m². Determine the increase in vertical stress, 3.5 m. deep at its center.
A circular area having a radius of 3 m carries a uniformly distributed of 90 kPa is applied to the ground. Compute the total vertical stress in kN/m^2 increment due to this uniform load if the unit weight of soil is 18.40 kN/m^3 at point 6 m below the center of the circular area. a. 27.26 b. 137.66 c. 129.02 d. 135.17
An elevated structure is supported on a tripod. The legs are spaced 4 m apart and form the apexes of an equilateral triangle. Compute the increase in the vertical stress at a depth of 3m (i) beneath the point of intersection of the angular bisector (ii) beneath the centre of one of the sides of the triangle if each one of the legs carries a concentrated load of 1000Kn. Explain with diagram.