Example 1 A step-down chopper fed from a 200-V source operates a dc motor whose armature EMF is 70 V and armature resistance is 0.5 Q. With the magnitude control ratio of 0.4, (A) Find the average output voltage and current of the chopper and determine the quadrant of operation. (B) The chopper operates with a switching frequency of 1 kHz and the armature inductance of the motor is 20 mH. i- Find the AC component of the armature current and ripple factor of the current, and ii- the ripple factor of the output voltage

Example 1 A step-down chopper fed from a 200-V source operates a dc motor whose armature EMF is 70 V and armature resistance is 0.5 Q. With the magnitude control ratio of 0.4, (A) Find the average output voltage and current of the chopper and determine the quadrant of operation. (B) The chopper operates with a switching frequency of 1 kHz and the armature inductance of the motor is 20 mH. i- Find the AC component of the armature current and ripple factor of the current, and ii- the ripple factor of the output voltage

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 4-quadrant DC chopper with bipolar switching operating at a switching frequency of 2kHz, is connected to a 120VDC source (Vs) and a DC motor which has a counter EMF (CEMF) of 50VDC at rated speed. The armature resistance is 2Ω and the armature inductance is 20mH. Calculate: a) Output voltage with an 80% duty cycle b) Magnitude and direction of the DC armature current with an 80% duty cycle. c) Duty cycle for a forward braking current of 10ADC. (Assume the speed has not changed due to the large inertia of the load.)
An AC motor is run from an AC supply connected to an AC voltage controller with firing angle of 30 degrees. If the motor operates at 100V RMS and draws a current of 10A, and there is a series resistance of 5ohm associated with the motor, what is the RMS voltage of the AC supply that needs to be connected to the AC voltage controller to drive the motor?
The transfer function of a DC motor is given as follows. Accordingly, obtain the amplitude and phase diagrams of the system and calculate the stabilities.
A shunt generator supplies a 30kW load at 215V through cables of resistance, R = 110mn. If the field winding resistance, Rf =680 and the armature resistance, Ra =45mn. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,
(a) Explain any two factors which justify the need of modulating a low frequency signal. (b) Write two advantages of frequency modulation over amplitude modulation.
Explain what is modulation?
A separately excited motor runs at 1045rpm, with a constant field current, while taking an armature current of 50A at 120V. The armature resistance is 0.1 Ω if the load on the motor changes such that it now takes 95A at 120V, determine the motor speed at this load.
Mcq Q1) What is the benefit of using two pulse transformers to drive the SCR of a single-phase bidirectional AC voltage controller? * - to isolate the SCRs from the source - to isolate the SCRs from getting short - to isolate the load from the source to control the rms output voltage
Consider the design of a home-built wind turbine using a 350-W automobile dc generator. The goal is to deliver 70 kWh in a 30-day month. 1- What capacity factor would be needed for the machine? 2- If the average wind speed is 5 m/s, and Rayleigh statistics apply, what should the rotor diameter be? 3- How fast would the wind have to blow to cause the turbine to put out its full 0.35 kW if the machine is 20% efficient at that point? 4- If the tip-speed-ratio is assumed to be 4, what gear ratio would be needed to match the rotor speed to the generator if the generator needs to turn at 1000 rpm to deliver its rated 350 W? 5- If Rayleigh statistics apply, what is the energy generated in a 30-day month when wind blows between its rated wind speed of 13 m/s and its furling wind speed of 25 m/s?
Find a) Percentage overshoot control system having the undamped natural frequency in rad/sec=8.6 and damping ratio =0.8
Also give the excitation table and transition table and state diagram too
In a DC motor with separately excited configuration, EMF voltage=D10xrotational speed of the rotor (or w). In addition, the resistance and the inductance of the armature are 5 Ohms and 200 mH, respectively. la and Va represent current and voltage of the armature and fit to the following transfer function: la/(Va+pxw)%3Dq/(s+r). What is r?