Example 1: Calculate the percent voltage regulation for a three-phase wye-connected 2500 kVA 6600-V turboalternator operating at full-load and 0.8 power factor lagging. The per phase synchronous reactance and the armature resistance are 10.4 2 and 0.071 S2, respectively? (b) o.8P.S bead paser diagram. H.W.: Repeat Ex.I calculations with unity power factor, and draw the phasor diagram for this case ?

Example 1: Calculate the percent voltage regulation for a three-phase wye-connected 2500 kVA 6600-V turboalternator operating at full-load and 0.8 power factor lagging. The per phase synchronous reactance and the armature resistance are 10.4 2 and 0.071 S2, respectively? (b) o.8P.S bead paser diagram. H.W.: Repeat Ex.I calculations with unity power factor, and draw the phasor diagram for this case ?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.41P

See similar textbooks

Similar questions

A 3-phase, wye connected alternator rated at 1600 kVA, 13.5 kV. The effective armature resistance and synchronous reactance are 1.5 ohms and 30 ohms, respectively. What is the percent regulation for a load of 1280 kW at 0.80 leading power factor?
• Zh = 100 ohm • Draw the pu reactance diagram by taking Ut(base) = 132kV, St(base) = 100MVA. If the 33 kV busbar voltage is kept constant at 30 kV and 0.8 inductive 50 MVA power is drawn from this bus, what is the voltage at the synchronous machine ends?
An AC generator having an internal resistance of 2 ?? is connected to an LCR circuit in series as shown in the figure. If the generator supplies an electromotive force, ? = 282 ??? (100??) volt, calculate:a) the impedance of the circuitb) the rms value of the current in the circuitc) the voltage drop across L, C and R
L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1450 rpm, line voltage 220 V and frequency 50 Hz star-connected 3-phase ASM, ignoring core (iron) losses given as follows: R1=0.21 Ohm, R2=0.18 Ohm, X1=X2=0.66 Ohm and Xm=9.9 Ohm How many times the rated current will the inrush current be when the ASM is started directly?
L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1450 rpm, line voltage 220 V and frequency 50 Hz star-connected 3-phase ASM, ignoring core (iron) losses given as follows: R1=0.21 Ohm, R2=0.18 Ohm, X1=X2=0.66 Ohm and Xm=9.9 Ohm How many times the inrush current will be the rated current when the ASM is started directly?
Discuss the significance of power generation, transmission, and distribution in the context of a reliable and efficient power supply. What are the challenges associated with each of these phases?
-) The active and reactive power drawn by the mixer fed from a 230 Vrms, 50 Hz single phase AC network was measured as 600 W and 100 VAR, respectively. According to this information: a) Calculate the apparent power drawn from the network? b) Calculate the current drawn from the network? c) Calculate the cos(a).
Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06 per unit has been added to the transformer and 0.05 per unit to the transmission line. Since the system is no longer lossless, a field showing the real power losses has also been added to the oneline. With the LTC tap fixed at 1.05, plot the real power losses as the phase shift angle is varied from 10 to +10 degrees. What value of phase shift minimizes the system losses?
At the end of the 8 km overhead line given in the figure below, there are two distribution transformers, one of which is 800kVA and the other is 1200kVA, operated with power coefficients of 0.6 and 0.8, respectively. The end-of-line voltage is 6kV. Find the required rated cross section and line head voltage so that the power loss on the line is less than %pk = 10.
Explain the importance of load flow analysis in power systems. How does it help in optimizing the operation of electrical grids?
In the context of power system analysis, explain the purpose and operation of a load flow study.