Example 12.3 :: The indirect FM system originally designed by Armstrong employed a NBFM , the oscillator frequency is 200 KHz, its desired in order to avoid distortion to limit the modulation index to 0.2, the system to accommodate modulation frequency down to 40 ¥Hz and output of the modulator, the carrier frequency is to be 108 MHz and Af = 80 KHz. Select the multiplier and mixer oscillator to accomplish this end

Example 12.3 :: The indirect FM system originally designed by Armstrong employed a NBFM , the oscillator frequency is 200 KHz, its desired in order to avoid distortion to limit the modulation index to 0.2, the system to accommodate modulation frequency down to 40 ¥Hz and output of the modulator, the carrier frequency is to be 108 MHz and Af = 80 KHz. Select the multiplier and mixer oscillator to accomplish this end

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.2P

See similar textbooks

Similar questions

answer all A - Explain the relation of MOSFET input current and input impedance and their effect on the functionality of the device. B- Explain how to increase the efficiency of the solar cells (PV cells) through the integration of antennas. C- List three conditions need to be considered to choose a MOSFET for switching applications.
What are the advantages and disadvantages of FM.
Consider the circuit of Figure 12.7 on page 605. Assume that VCC=20 V, VBB=0.3 V, RB=40 kΩ, and RC=2 kΩ. The input signal is a 0.2-V-peak 1-kHz sinusoid given by vin(t)=0.2 sin(2000πt). The common-emitter characteristics for the transistor are shown in Figure P12.18. Determine the maximum, minimum, and Q-point values for vCE. What is the approximate voltage gain for this circuit? Why is the gain so small in magnitude?
TOPIC: AMPLITUDE MODULATION AND DEMODULATIONPlease answer this 2 question thanks.1. What is the different degree of modulation?2. What are the limitations of square law modulator?
What is the condition for over modulation and what are its effects?
a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?
Q2 (A) A frequency modulator is supplied with a carrier at frequency fc = 5 MHz and an audio tone signal of Am = 1 volt amplitude and frequency fm = 1 kHz. It produces a frequency deviation f of 10 kHz as the output of the frequency modulator. (3)(i) The FM waveform described above is passed through a frequency multiplier with a total multiplication factor of 18, that is, fout = 18*fc. After passing through the frequency multiplier, what is the frequency deviation f at the output?(ii) The output of the multiplier in part (a) is next input to a mixer stage with the LO oscillator frequency set at fLO = 55 MHz. Find the sum-frequency output fo of the mixer’s IF port and also find the magnitude of the frequency deviation f.
Discuss the concept of multiplexing and its importance in optimizing bandwidth utilization.
Briefly describe the effects the switching control signal frequency has on the output voltage and current of a boost chopper. In Dhaka city during the month of May, a 20W rated solar panel supplies 15W of power at an output voltage of 15V & an output current of 1A. But during the month of December, the same solar panel supplies 8.5W of power at an output voltage of 10.5V & an output current of 0.81A. The solar panel is used to charge a 12V battery. Practically, for charging a 12V battery we need to supply 13V.i) In the month of May, the user will need a DC-DC converter (Buck) to charge the battery.a) What will be the duty cycle?b) Assuming that the converter is 100% efficient, what will be the input current to the battery?ii) In the month of December, the user will need a different DC-DC converter (Boost) to charge the battery.a) What will be the duty cycle?b) Assuming that the converter is 100% efficient, what will be the input current to the battery?
Describe the process of Filteration?
What Is frequency modulation and demodulation? Describe their importance and how they work.
For an efficient communication in PCM system, the number of samples per second must be at most be equal to twice the highest modulating frequency.a. A very important considerationb. No, it must be at least equal to twice the highest modulating frequencyc. 80-50 percent true