Example 26.20(b). A four-pole, lap-wound shunt generator has 300 armature-conductors and a flux/pole of 0.1 Wb. It runs at 1000 r.p.m. The armature and field-resistances are 0.2 ohm and 125 ohms respectively. Calculate the terminal voltage when it is loaded to take a load current of 90 A. Ignore armature reaction. (Nagpur University, April 1999)

Example 26.20(b). A four-pole, lap-wound shunt generator has 300 armature-conductors and a flux/pole of 0.1 Wb. It runs at 1000 r.p.m. The armature and field-resistances are 0.2 ohm and 125 ohms respectively. Calculate the terminal voltage when it is loaded to take a load current of 90 A. Ignore armature reaction. (Nagpur University, April 1999)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.24P: For Problem 3.18, the motor operates at full load, at 0.8 power factor leading, and at a terminal...

See similar textbooks

Similar questions

A shunt generator supplies a 31kW load at 230V through cables of resistance, R = 122mΩ. If the field winding resistance, Rf =50Ω and the armature resistance, Ra =51mΩ. Determine the following below: The terminal voltage is, Answer and unit for part 1 The e.m.f. generated in the armature is,
A 3 phase, star connected synchronous generator supplies current of 10A having phase angle of 20º lagging at 400V. Find the load angle and the components of armature current Id and Iq if Xd = 10 ohm and Xq = 6.5 ohm Assume armature resistances to be negligible
A short shunt compound generator supplies a load of 10 kW at 200 V through a pair of feeder and series field resistance 0.10 ohm. Armature resistance, shunt field resistance and series field resistance are 0.01 ohm, 52.2 ohms and 0.10 ohm, respectively. If the core friction and windage losses amount to 631 watts, the BHP of the driving engine is nearest to
Show that an alternator running in parallel on constant-voltage and frequency bus-bars has a natural time period of oscillation. Deduce a formula for the time of one complete oscillation and calculate its value for a 5000-kVA, 3-phase, 10,000-V machine running at 1500 r.p.m. on constant 50-Hz bus-bars. The moment of inertia of the whole moving system is 14,112 kg-m2 and the steady short-circuit is five times the normal full-load value. ANSWER IS [1.33 second]
A 11 kV, 50 Hz, four-pole, star-connected alternator is being synchronised on an infinitebus. On the moment of synchronising, the excitation is such that the induced emf is 10%too low and the synchronising angle is 8° electrical leading. If the synchronous reactanceis 6 Ω/phase, determine the torque at synchronising. Mention the necessary assumptions.
A gas turbine, 2-pole, 3? synchronous generator rated at 200 MW is connected to the grid (presumed to be an infinite bus). The electrical operating frequency of the grid is 60 Hz, and the slope of the frequency-power curve for the generator is 15 MW/Hz. a. If the no-load setpoint for the generator is set to 63.5 Hz, how much active power will the generator provide to the grid? b. Neglecting system losses, what is the torque provided by the gas turbine? c. What would happen if the no-load setpoint for the generator is set to 59 Hz?
The synchronous reactance of a generator is 1.0 per unit, and the leakage reactance of itsarmature is 0.1 per unit. The voltage to neutral of phase a at the bus of a large system to which the generator is connected is 1.0∠0 ◦ per unit, and the generator is delivering a current Ia = 1.0∠− 30◦ per unit. Neglect resistance of the winding and find:a. the voltage drop in the machine due to armature reactionb. the internal voltage to neutral E of phase a of the generatorc. the per unit values of P and Q delivered to the bus Note: Equivalent circuit is shown in Fig. 1 where Xar armature reactance, Xl leakagereactance, and XS synchronous reactance
For Problem 3.18, the motor operates at full load, at 0.8 power factor leading, and at a terminal voltage of 10.45 kV. Determine (a) the voltage at bus 1, which is the generator bus, and (b) the generator and motor internal EMFs.
Q23) A shunt generator supplies a 20KW load at 200V through cables of resistance, R = 100mΩ. If the field winding resistance ,Rf=50Ω and the armature resistance, Ra=40mΩ, i) Estimate terminal voltage across the load. ii) Calculate the emf generated in the armature.
(a) A short shunt cumulative compound dc generator supplies 6kW at 235V. The Shunt field resistance, Series field resistance and Armature resistances are 8012, 0.192 and 0.22 respectively. Calculate the induced emf and load resistance.
111/ The armature reaction of the DC generator reduces the generated EMF. Select one: True False
Q/ dc shunt generator 4 pole with 500 condcutor , wave running at speed 1000 r.p.m the resistance of armature and field are 0.02 , 55 ohm and delivering load 43.12kwatt at terminal voltage 220 volt, the iron losses is 750 watt 1-Torque developed by the prime mover .........and The torque developed by the armature ........... when running at 1000 r.p.m * 2-The load current ,,,,,,,,,,,,when the speed drops to 800 r.p.m. if If is unchanged ? * 3-Output of the prime motor…….kwatt * 4-Mechanical , electrical and overall efficiency …….. * 5-Flux per pole is......... wb *