Example 3A 0.5 kg object travelling with a speed of 12m/s impacts a springone side of a spring which is supported by a wall at the oppositeend. Assuming an infinitely long spring that will not buckle,determine the maximum reaction force at the wall and thedisplacement in the spring to bring the ball to rest if the spring hasa stiffness of 1000 Nm, 5000 Nm and 10000 Nm.Vreeeeeeed

Answered: Image /qna-images/answer/9d143338-f7b7-4851-bed1-c6e14bb427bc.jpg

Example 3 A 0.5 kg object travelling with a speed of 12m/s impacts a spring one side of a spring which is supported by a wall at the opposite nd. Assuming an infinitely long spring that will not buckle, letermine the maximum reaction force at the wall and the lisplacement in the spring to bring the ball to rest if the spring has stiffness of 1000 Nm, 5000 Nm and 10000 Nm. --●reeeeeeed

Example 3 A 0.5 kg object travelling with a speed of 12m/s impacts a spring one side of a spring which is supported by a wall at the opposite nd. Assuming an infinitely long spring that will not buckle, letermine the maximum reaction force at the wall and the lisplacement in the spring to bring the ball to rest if the spring has stiffness of 1000 Nm, 5000 Nm and 10000 Nm. --●reeeeeeed

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.48P: Find the smallest distance d for which the hook will remain at rest when acted on by the force P....

See similar textbooks

Similar questions

Forming a shock absorber, two springs of equal length are nested together. If the maximum compression of the springs is 0.25 and the outer spring has a stiffness of Ka = 420 N/m, what stiffness is required of the inner spring Kb? The design of the spring system is such that if a mass of 2.5 kg is at rest, then dropped from a distance of 0.75 m above the springs, the spring system will catch and stop the mass.
Read the question carefully and give me right solution A slender rod with a length of 40 cm and a mass of 2 kg is falling at a rate of 1.5 m/s and at a 35-degree angle as shown below. The rod then strikes a surface and rebounds off it. Assuming that the coefficient of restitution for the impact is .9, and that there is negligible friction between the body and the surface,what is the expected velocity of the center of the rod (C) and the angular velocity immediately after impact?
A body with a mass of m=20 kg is at rest in the vertical circular cylinder in the picture at a height h from the rigid base plate. The piece slides frictionlessly in the cylinder and hits the bottom plate under the influence of gravity g=9.81 m/s^2. The collision is completely inelastic and the bottom plate is completely rigid. The cross-sectional area of the cylinder is A=1500 mm^2, the elastic coefficient of the material is E=70 GPa and the length of the pipe is L=1.0 m. Present the responses of the system to displacement, velocity and acceleration. How high can the mass be dropped without an initial velocity so that the amplitude of the oscillation does not increase more than 1 mm?
A block weighing 2.50 kg begins its motion from a stationary position at point A, located at the highest point of a frictionless ramp. The ramp is inclined at an angle of 40° relative to the horizontal and has a length of 1.50 m. As the block slides down the ramp, it reaches a region between point B and point C, which is a rough horizontal surface with a kinetic friction coefficient of 0.30. After covering a distance of 1.00 m on the horizontal surface, the block encounters a lightweight spring with a spring constant of 900 N/m. A. Find the total energy for point A and point B? B. Find the speed of the block at point B? C. What is the cumulative work performed on the block as it moves along the rough horizontal surface? D. By employing the work-energy theorem, determine the velocity of the block at point C just before it collides with the spring?
A machine part consists of a thin 0.6 m long bar with small 1 kg masses fastened by screws to its ends. The screws can support a maximum force of 65 N without pulling out. This bar rotates about an axis perpendicular to it at its center. As the bar is turning at a constant rate on a horizontal frictionless surface, what maximum speed the masses can have without pulling out the screws?
A test of an energy-absorbing bumper, a 1270 kg car is drive into a barrier at 8 kph. The duration of the impact is 0.4 sec and the car bounces back from the barrier at 1.6kph. What is the maginitide of the average horizontal force on the car during the impact?
The design for a new cementless hip implant is to be studied using an instrumented implant and a fixed simulated femur. Assuming the punch applies an average force of 2 kN over a time of 2 ms to the 200-g implant, determine (a) the velocity of the implant immediately after impact, (b) the average resistance of the implant to penetration if the implant moves 1 mm before coming to rest.
The motion of a steel ball in a hemispherical bowl of radius h shown in fig is to be analyzed. The ball is initially held at the highest location at point A, and then it is released. Obtain relations for the conservation of energy of the ball for the cases of frictionless and actual motions.
A 25.0-kg homogeneous boulder, initially at rest, is being pulled by a force P directed 10.0° northeast as shown. The coefficients of nonsliding and sliding friction between the boulder and the ground are 0.450 and 0.350, respectively. For what value of force P will the boulder start to slide? For what value of force P will the boulder start to tip forward?
The figure shows a junction of mass m = 10kg sliding on a rod in a vertical plane. Positioned 1 simpai is stationary and horizontal spring and tensioned Fp = 300N. If the spring constant is k = 1kN/m and the average frictional force between the rod and the junction is F = 30N. Calculate the speed at position 2. (Ans: 3.47m/s)
A small 2-lb ball B is rotating (Fig.13) at angular speed w1 of (6+(0.1*26)) rad/sec about a horizontal shaft. The ball is connected to the bearings with light elastic cords which when unstretched are each 12 in. in length. A force of 15 lb is required to stretch the cord. The distance d1 between the bearings is originally 20 in. If the bearing A is moved to shorten d by 6 in, what is the angular velocity w2 of the ball? Neglect the effects of gravity and the mass of the elastic cords. Use the moment of momentum equation.
To climb a 400 meter high mountain, you have two options, a straight line route with a 40 ° slope or a route composed of 5 equal sections (same length) each with a 20 ° slope. If traveling in a car with a mass of 1280 kg and a maximum power of 88 kW, Determine (assume the whole car as a particle): a) Is the friction enough to prevent the car from sliding? The coefficient of static friction of the tires with the ground is 0.95. b) What is the power required to climb the 40 ° slope at a constant speed of 40 km / h? Does the car have enough power to go up at that speed? c) What is the constant speed at which the 40 ° slope can be climbed with a 60 kW power? d) What is the power required to climb a 20 ° slope at 40 km/h? Does the car has enough power to go up at that speed? e) In which of the two trajectories does the car do more work? Ignore the resistance of the air and rolling resistance and radius of curves between sections of the compound route. Please add the free body diagram.