Example 4.2.3: The part shown below will be turned in two machining steps. In the first step a length of (50 + 50) = 100 mm will be reduced from Ø100 mm to Ø80 mm and in the second step a length of 50 mm will be reduced from Ø80 mm to Ø60 mm. Calculate the required total machining time T with the following cutting conditions: V=80 m/min, f=0.8 mm/rev, D.O.C = 3 mm per pass. Ø100 Ø80 Ø60 50 50

Example 4.2.3: The part shown below will be turned in two machining steps. In the first step a length of (50 + 50) = 100 mm will be reduced from Ø100 mm to Ø80 mm and in the second step a length of 50 mm will be reduced from Ø80 mm to Ø60 mm. Calculate the required total machining time T with the following cutting conditions: V=80 m/min, f=0.8 mm/rev, D.O.C = 3 mm per pass. Ø100 Ø80 Ø60 50 50

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A slab-milling operation is carried out on a 200 mm long, 80-mm-wide annealed mild-steel workpiece having a feedrate of 0.1 mm/tooth and a depth of cut of 4.0 mm. The cutter of 50 mm diameter has 18 straight teeth and rotates at 135 rpm. The given specific energy for this material is 3.5 W s/mm3 and the slab mill is wider than the workpiece to be machined. Calculate:‧ the material-removal rate;‧ the power and torque required for this operation;‧ the cutting time. (243 mm/min, 77760 mm3/min, 4.5 kW, 52.8 s)
A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm thickness at rate of 35 holes per minute. It requires a torque of 7 Nm for an area of hole in mm2. If the cutting takes 1/10 of a second and the speed of its flywheel varies from 165 rpm to 145 rpm, calculate:
Draw the forces and angles involved in the cutting process and calculate shear angle (0), friction coefficient and tangential force if ,cutting force = 80 kN, resultant of forces =100kN, friction force=75kN, rake angle =20° undeformed chip thickness = 0.65mm and deformed chip thickness = 0.72mm
Suppose in a face milling operation, the dimensions of the workpiece are 5 inches by 10 inches. The cutter is 6 inches in diameter, has 8 teeth, and rotates at 300 rpm. The depth of cut is 0.125 inches and the feedrate is 0.005 inches / tooth. Assume that the specific power requirement for this material is 2 hp min / in3 and that only 75% of the cutter diameter is involved in cutting. Calculate (a) the required power, and (b) the material removal rate.
Find the machining time, in seconds, and the rate of material removing in mmA3;sec for a turning operation having the following information: 1- Wp diameter is 80mm, 2- the length is 0.12m, 3- the cutting speed is 80m/min, 4- feed i50.5 mm/rev and 5- the depth of cut is 0.002m.
Draw the forces and angles involved in the cutting process and calculate shear angle (Ø), friction coefficient and tangential force ,cutting force = 80 kN, resultant of forces =100KN. friction force=75KN, rake angle =20' undeformed chip thickness = 0.65mm and deformed chip thickness = 0.72mm vjall
A flat milling operation will be carried out with a horizontal milling machine, in a piece of 250 mm in length and 50 mm in width, using a felicoidal bur with a diameter of 75 mm, with 10 teeth. If the feed per tooth is 0.2mm, and the cutting speed is 0.75 m / s, how would you determine the speed of metal removal to remove 6 mm from the surface of this piece?
A turning operation is made with a rake angle of 10 degrees, a feed of 0.010 in/rev, and a depth of cut = 0.100 in. The shear strength of the work material is known to be 50,000 lb/in2, and the chip thickness ratio after the cut = 0.40. Determine the cutting force and the thrust force. Use the orthogonal cutting model as an approximation of the turning process.
During a certain machining experiment at the UCSI workshop, it is observedthat temperature at the tool workpiece interface is 1200 oC at a cutting speed of300 mm/min with a feed rate of 0.002 mm/rev. (i) Analyse how the temperature will be affected if the cutting speed isincreased by 100 %.(ii) Determine the cutting speed necessary to achieve a maximum cuttingtemperature of 900 oC
A motorised metal guillotine machine is required to cut 45 mm diameter hole ina plate of 20 mm thickness at rate of 35 holes per minute. It requires a torqueof 7 Nm for an area of hole in mm?. If the cutting takes 1/10 of a second andthe speed of its flywheel varies from 165 rpm to 145 rpm, calculate:1.Energy required to cut a hole.2.Energy required for cutting work per second.3.Maximum fluctuation of energy of the flywheel.4.Mass of the flywheel having radius of gyration of 1.5 m.
For the following application, identify one or more nontraditional machining processes that might be used, and present arguments to support your selection. Assume that either the part geometry or the work material (or both) preclude the use of conventional machining. The application is a matrix of 0.1 mm (0.004 in) diameter holes in a plate of 3.2 mm (0.125 in) thick hardened tool steel. The matrix is rectangular, 75 by 125 mm (3.0 by 5.0 in) with the separation between holes in each direction = 1.6 mm ( 0.0625 in).
A 78 mm thick plate is to be milled down to a thickness of 60 mm using an 80 mm face milling cutter. Calculate the processing time if the cutting depth is 6 mm, the feed/rev is 1.1 mm and the cutting speed is 15 m/min, and if the over run for a 620 mm long plate is 10 mm.