Example (5): In a variable capacitance transducer the diaphragms are 20 mm in diameter and 4 mm apart. If a pressure produce an average deflection of 0.25 mm, calculate the value of capacitance after the application of force. The capacitance before the application of force is 400 pF. H.W

Example (5): In a variable capacitance transducer the diaphragms are 20 mm in diameter and 4 mm apart. If a pressure produce an average deflection of 0.25 mm, calculate the value of capacitance after the application of force. The capacitance before the application of force is 400 pF. H.W

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. A parallel plate capacitor with a plate area of 0.13 square meters separated by 1 mm is charged to 9 Volts by a battery, which is then disconnected. The plate separation is then increased to 40 mm.A. Using the expression for the capacitance of a parallel plate capacitor, what do you expect the new potential difference across the plates to be after the increase?B. Suppose you measure the potential difference across the plates after the separation and find it to be 30 V (this should be very different from what you found in part A). This unexpected result can be explained by the effects of “stray capacitance” with nearby objects. Assuming that the stray capacitance can be modeled as a capacitor connected in parallel with the parallel plate capacitor, find the value of this stray capacitance.
1. The capacitive network shown in the figure is assembled with initially uncharged capacitors. A potential difference, Vab = +100V, is applied across the network. The switch S in the network is kept open. Assume that all the capacitances shown are accurate to two significant figures. What is potential difference Vcd across the open switch S?
Using GRSA(Given, Required, Solution, Answer) method provide 1 sample problem and steps in solving using formula in capacitance.
A solid specimen of dielectric dielectric constant of 4.0, shown in the figure has an internal void of thickness 1mm. The specimen is 1cm thick and is subjected to a voltage of 80 kV(rms). If the void is filled with air and if the breakdown strength of air can be taken as 30 kV(peak)/cm, find the voltage at which an internal discharge
A 0.8-F capacitor is connected in series with a 7-ohm resistor. If the connection is energized from a 10-V DC source, determine which among the following is a differential equation describing the circuit? Let q be the amount of charge in the circuit at any time t.
A paper dielectric plate capacitor is to be experimentally tested. The metal plates and the paper material between said plates are all 20 cm in radius and subjected to 10V dc in the test. How much is the capacitance does this capacitor have in picofarads (pF), if the paper material between plates used is 2 cm thick? Input answer in 4 decimal places and in pF. Note: Relative permittivity of the paper ( εr ) : 0.4225
the emf source, E=3.2 V, of the circuit shown in the figure has negligible internal resistance. the resistors have resistances R1=3 ohm and R2=4.2 ohm. the capacitor has a capacitance C= 3.1uF. A) determine the time constant t , in units of microseconds for charging the capacitor. B) what is the charge Q on the capacitor in units of microcoulomb?
Vbatt=25 VC1=90 ?CC2=75 ?CC3=60 ?CR1=160 ΩR2=120 Ωt2=21.6 msect3=27 msecConsider the circuit shown below which shows a battery connected to some resistors and capacitors along with some switches which will be toggled opened or closed at different times. The components are listed above. The capacitances are in microFarads (?F), the resitances are in Ohms (Ω), and the times are in milliseconds (msec). A stopwatch is started at time t1=0 ms. At that time, switch S1 is closed and all other switches are open and the capacitor is allowed to charge up.(a). (i)What is the charge (in uC) on C1 at the time the stopwatch reads t2=21.6 ms?a)3690 b)1520 c)5710 d)2630 e)683 f)1750 (a).(ii)What is the current (in mA) through R1 at t2=21.6 ms?34.9 30.4 114 13.6 73.6 52.4 (b)(i)What is the voltage (in V) across R1 at t2=21.6 ms?8.37 5.58 2.18 11.8 18.2 4.85(ii). What is the voltage (in V) across C1 at t2=21.6 ms?63.2 29.1 40.9 7.57 19.4 16.9(c). (i) What is the energy (in mJ) in C1 at t2=21.6 ms?6.63…
. A parallel-plate capacitor has a plate separation d and plate area A. An uncharged metallic slabof thickness t is inserted midway between the plates. Determine the:a. Find the capacitance of the device.b. Show that the capacitance is unaffected if the metallic slab is infinitesimally thin.
A capacitance of 5 uF, if the current given in the graph below is applied, what would the voltage on the capacitance be, t = 30 us (microseconds)?
For the circuit shown in the figure, in which the capacitor is initially fully discharged. If the source voltage V is 17 Volts, the capacitance of capacitor C is 24 mF; and the values of the resistors in Ω are: R1 = 2250 , R2 = 1071 , R3 = 2455 , R4 = 1199 and R5 = 1043 Determine the voltage across the capacitor in Volts after 15 minutes have elapsed since the circuit is energized. ..
Determine the total capacitance, in nF, of a parallel-plate capacitor having three dielectrics in between where the individual capacitances in nanofarads are 71, 90, 19, respectively.