Example 5.12. Five strings are tied at a point and are pulled in all directions, equally spaced from one another. If the magnitude of the pulls on three consecutive strings is 50 N, 70 N and 60 N respectively, find graphically the magnitude of the pulls on two other strings. 70 N 60 N B) 72° 72° 72° 50 N 72° 72° P1 (A (E P2 Match each item to a choice: P2 P1 Choices: E 87.4N : 65.3N : 27.5N : 57.5N : 75.7N : 36.5N : 72.5N E 48.7N E ON

Example 5.12. Five strings are tied at a point and are pulled in all directions, equally spaced from one another. If the magnitude of the pulls on three consecutive strings is 50 N, 70 N and 60 N respectively, find graphically the magnitude of the pulls on two other strings. 70 N 60 N B) 72° 72° 72° 50 N 72° 72° P1 (A (E P2 Match each item to a choice: P2 P1 Choices: E 87.4N : 65.3N : 27.5N : 57.5N : 75.7N : 36.5N : 72.5N E 48.7N E ON

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

* Question Completion Status: 5 6 OL Distributed load, w = 1.10 MN/m ag, h = 42 Distance, a = 34 7 The cable supports a railway bridge between two tunnels. Given: 9 a 10B What is the maximum tension (MN) in the cable? Express your answer in 2 decimal place. 12 13 150 160 17 18 19 20
I have the force vectors but I am having trouble getting the distance vector
Question # 12: Calculate the approximate internal MOMENTS at point A and point B due to the vertical loading shown in the figure below. 10 k 10 k 10 k 10 k F > 5 k 20 ft D |B 20 ft 20 ft 20 ft निर्देश: अपने अंतिम उत्तर बॉक्स करें।
Consider the beam shown in (Figure 1). EI is constant Follow the sign convention Part A Vj = coordinate for 0 Szi 디스플 Determine the equation of the elastic curve for the beam using the Express your answer in terms of some or all of the variables 21, L. E, I. and Mo. Express the coefficients using three significant figures. Submit Patt NO IVE ΑΣΦΗ Η Mo M₂ 12 vec Previous Answers Best Answer 4 Determine the equation of the eastic care to the bearing the co Express your answer in terms of some or all of the variat VALEC Incorrect; Try Again 5 attempts maing 24EIL-4x+122x,²-112²x, +32²] 2 L.E.I. ad M. Express the coefcends using these significant figu
In (Figure 1), F = {80i + 96j + 48k} lb. Figure 1 ft -2 ft 3 ft 45° B 1 of 1 Part A Determine the magnitude of the moment of F about point A. Express your answer in pound-feet to three significant figures. 15] ΑΣΦ11 MA = Submit Part B α, B, y = Submit Request Answer Provide Feedback Determine the coordinate direction angles of the moment of F about point A. Express your answers in degrees to three significant figures separated by commas. vec U/ ΨΕ ΑΣΦ ↓↑ vec Request Answer ? lb. ft ? Next >
A 50 m tape weighing 0.049 kg/m with a cross-sectional area of 0.05 sq. cm and modulus of elasticity equal to 2x106 kg/cm2 is used in determining the distances between two points. The tape is of standard length under a pull of 6.70 kg and a temperature of 25°C when supported throughout its entire length. The tape was then used in the field to measure a distance that was determined to be 378.123 m. At the time the measurement was made, the constant pull applied was 9 kg with the tape supported only at endpoints. During the measurement the recorded temperature was 17°C. Use o=11.6x10-6/C. Determine the correct length (in feet)of the line. Youranswer
A 30-m tape of 0.05 kg/m weight was used to measure a distance. The measured length is 800 m. During measuring, the pull at ends of the tape is recorded to be 30 kg. Calculate the following: a. Error in measurement if the tape is used with its ends supported. b. Corrected length if the tape is used with its ends supported. c. Corrected length if the tape is supported at every 15 m.
Question 21 3.5 m A C 5.5 m 0.2 m X B D G Time left 0:58:42 In the figure above, the jib crane is supported by a pin at C and rod AB. Knowing that x = 5.7 m, and the load D has a mass of 3000 kg, with its center of mass located at G, you are required to explain your answers by your own words and A) Draw the free body diagram (FBD) [ B) Determine the reactions at the pin C C) Determine the force developed in rod AB D) Check the equilibrium of the system by determining the sum of the moments of all forces about point B 1.
How to solve this question step by step