Player 001 decided to create a 2-kg hanging figurine display as shown. The display is held in equilibrium by a hinge at F and a lightweight cable attached at point C. He placed figurines with varying sizes such that their weights approximate a triangular distributed load on side AB as shown. 3.00 N/m A .800 m F 1.200 m 0.600 m 5. Which of the following approximates the magnitude of the tension force?

Player 001 decided to create a 2-kg hanging figurine display as shown. The display is held in equilibrium by a hinge at F and a lightweight cable attached at point C. He placed figurines with varying sizes such that their weights approximate a triangular distributed load on side AB as shown. 3.00 N/m A .800 m F 1.200 m 0.600 m 5. Which of the following approximates the magnitude of the tension force?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Optimum Mechanics Co. lifted a car weighing 3184 lbf using the system presented. The platform was supported by four (4) cables (Cable AB, AC, AD, and AE). Determine the following: (Take AB = AE). note: Express your answer in units.Observe 3 decimal places.The error threshold is ± 2.50% Relative to the right answer. A: < 0 0 10.143 >ft B: < 4.954 4.997 0 > ft C: < 6.66 -4.997 0 > ft D: < -7.029 -4.534 0 > ft E: < -5.439 4.997 0 > ft 1.) Determine the TENSION IN CABLE AE.
for the 3rd Digram moment why is it +180 or how did they came up with 180
21 - At point O in the figure F1 = 27i + 29j F2 = -32i + 14j F3 = -16i - 8j F4 = -24i - 15j Find the sum of the vectors. What is the magnitude of the resultant vector? A) 47.03B) 50.26C) 55.62D) 49.24E) 45.39
If a force of 420 N is required to push a safe up a ramp that is inclined 10ᵒ, then what is the weight of the safe? Neglect friction. A. 2542.3B. 2418.7C. 2365.5 D. 2278.9
If the block is 1000jg, determine the value of force P(N) that is causing the movement of the block usubstatic=0.50 and usubkinetic=0.35. A. 4700N B. 5000N C. 0 D. 4905N
A line was recorded as 1750.00 meters long. The standard tape weighs0.65 kg , 30.00m long at 20°C under a 50N pull. During the actualobservation the temperature was 5°C and the tape was suspended undera 75N pull. It was also found that the tape is 3.00mm too long. If the linewas inclined at 3%. E = 200GPa, A = 2.50mm² and the coefficient of linearexpansion is 0.0000116 m/°C.(a) What is the actual inclined distance?(b) What is the actual horizontal distance.
A spring is used to stop a 55 kg package which is sliding on a horizontal surface. The spring has a constant k = 18 kN/m and is held by cables so that it is initially compressed 99 mm. The package has a velocity of 2.6 m/s in the position shown and the maximum deflection of the spring is 32 mm. Determine the work (J) done by friction as the package moves back to its initial position knowing that x=543 mm. Round off only on the final answer expressed in 3 decimal places. Note: Consider that work can either have a positive or negative sign.
28. Situation 10 - An object (SG = 7.3) floats in mercury (SG = 13.6) such that a certain portion is above the liquid surface. a. What fraction of the volume of the object floats above the surface of the mercury? Round off to three decimal places. b. If the volume of the object below the liquid surface is 0.014 m3, what load, in kN, applied vertically that would cause the object to be fully submerged? Round off to two decimal places. c. If the volume of the object below the liquid surface is 0.014 m3, what is the weight, in kN, of the object? Round off to two decimal places.
Figure No. 5 Given q = 100 N/m, P = 60 N and Mo = 1000 N.m. L1 = 5m, L2 = 2m, and L3 = 2m
Question-02:(CLO2)(10)A closed container containing water up to a height of 3.0 meter and air at the upper part with an orifice of 100 mm at its bottom. If 50% of the air is being removed from the upper part of the container by suction then Estimatedischarge passing through the orifice using Bernoulli’s equation if Cd=0.62.
Fast pls solve this question correctly in 5 min pls I will give u like for sure Mnty Find the moment of inertia of a plate covering the region bounded by -6x, 6x, y=0, and y =1with respect to the x-axis.
How was this 0.68 V2 calculated? And also 40.77 f V2 because I am not getting that..