Example/ A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected to an internal pressure of 4.5 MN/m 2. (a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the internal pressure be increased if the stress in the steel is limited to 120 MN/m 2 ?

Example/ A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected to an internal pressure of 4.5 MN/m 2. (a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the internal pressure be increased if the stress in the steel is limited to 120 MN/m 2 ?

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.25P: Refer to Figure 8.27. The flexible area is uniformly loaded. Given: q = 300 kN/m2. Determine the...

See similar textbooks

Similar questions

Refer to Figure 8.27. The flexible area is uniformly loaded. Given: q = 300 kN/m2. Determine the vertical stress increase at point A located at depth 3 m below point A (shown in the plan). FIG. 8.27
A cylindrical steel pressure vessel with a diameter of 1200 mm and a wall thickness of 20 mm is subjected to an internal pressure of 4.5 MPa. To what value could the internal pressure be increased/decreased if the allowable design stress is 120 MPa?
A thick cylinder 1 meter inside diameter and 7m long is subjectedto an internal fluid pressure of 40MPa. Determine the thickness of the cylinder ifthe maximum shear stress in the cylinder is not to exceed 65MPa. What will be theincrease in the volume of the cylinder? E=200GPa, μ= 0.30.
An upright cylindrical water tank having a diameter of 3 meters and a height of 6 meters is to be completely filled with water. Determine the minimum thickness of the tank plate if the stress is limited to 20 MPa.
A large uniform cylindrical steel rod of density ρ = 8.8 g/cm3 is 4.0 m long and has a diameter of 5.0 cm. The rod is fastened to a concrete floor with its long axis vertical. What is the normal stress in the rod at the cross section located at (a) 2.0 m from its lower end? (b) 2.5m from the lower end? Your answer
The column is constructed from high-strength concrete and eight steel reinforcing rods. If thecolumn is subjected to an axial force of 200 kips, determine the average normal stress in theconcrete and in each rod. Each rod has a diameter of 1 in. ?????? = 30,000 ??? and ????????? =4,000 ???.
Find the limiting peripheral velocity of a rotating steel ring if the allowable stress is 42 ksi and steel weighs 490 lb/ft^3. At what revolutions per minute (rpm) will the stress reach 30 ksi if the mean radius is 10 in.?
A thin-walled cylindrical steel water storage tank 30 ft in diameter and 60 ft long is oriented with its longitudinal axisvertical. The tank is topped with a hemispherical steel dome. The wall thickness of the tank and dome is 0.75 in. Ifthe tank is pressurized to 50 psig and contains water 55 ft above its base, and considering the weight of the tank,determine the maximum state of stress in the tank and the corresponding principal stresses (normal and shear). Theweight density of water is 62.4 lbf/ft3
What would be the change ineffective stress at point A if the water table rises to 2m above ground level? see figure below a. lower b. higher c. no change in effective stress?
a cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, can only be subjected to a maximum stress value of 120MN/m^2. if the same amount of pressure is applied/ contained in a spherical vessel whose internal volume is 0.075m^3, what must be the sphere's material thickness if it is experiencing a stress value of 127.484 MN/m^2. the radial stress for spherical vessel is theta sub s equals pD/4t
The propeller shaft of a large ship has outside diameter 18in. and inside diameter 12in., as shown. The shaft is rated for a maximum shear stress of 4750psi.a. If the shaft is turning at 100rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress?b. If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
A cylindrical steel pressure vessel with a diameter of 1200 mm and a wall thickness of 20 mm is subjected to an internal pressure of 4.5 MPa. Determine the circumferential stress in the tank.