Example viscosities µ' and µ" on the two sides of the plate. The plate is pulled at a constant velocity V. Calculate the position of plate so that : The shear force on the two sides of the plate is equal (i) The force required to drag the plate is minimum. Assume viscous flow and neglect all end effects. A thin plate of very large area is placed in a gap of height h with oils of Position of the plate, y: Thin plate

Example viscosities µ' and µ" on the two sides of the plate. The plate is pulled at a constant velocity V. Calculate the position of plate so that : The shear force on the two sides of the plate is equal (i) The force required to drag the plate is minimum. Assume viscous flow and neglect all end effects. A thin plate of very large area is placed in a gap of height h with oils of Position of the plate, y: Thin plate

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.50P

See similar textbooks

Similar questions

Air at 1000C flows at an inlet velocity of 2 m/s between two parallel flat plates spaced 1 cm apart. Estimate the distance from the entrance to the point where the boundary layers meet.
Air is flowing parallel to the plate at U∞=5 m/s and T∞=300 K over the flat plate of length L=0.1 m anddepth of 1 m into the paper, at the atmospheric pressure at the same temperature as the plate. Find;a) Boundary layer thickness at the point x = L of the plateb) Find the total resistance force acting on the two surfaces of the plate.c) The velocities in the hydrodynamic boundary layer are measured by a hot wire anomemeter. Thevelocity at x=0.1 m on the x component is measured as u=3 m/s. Find the distance from the plate and they component of velocity v.
An 16-kg slab slides down a 25° inclined plane on a 4-mmthick film of SAE 30 oil at 15.6 °C; the contact area is0.3m2. Find the terminal velocity of the slab. Explain ur answer
Q. 6 A 4.5-cm wide space between two plates is filled with SAE 30W lubricating oil at 26.7°C (Hoil = 0.301645 N.S/m2 ). What is the area of a very thin plate which is dragged by a force of 18 N through the oil at velocity of 16 m/min if the plate is 1.5 cm away from one of the fixed surfaces?
As given in the figure below, a square block weighing 1.1 kN has a 20° inclination and is 0.25 m x It moves on a 6 μm thick oil layer with a 0.25 m surface area. linear Calculate the maximum velocity the block can reach with a flow profile. (μoil = 7 x 10-3 Pa.s)
Consider a commercial airliner flying at a speed of 540 mph (relative to the air) at analtitude of 30,000 feet. (c) With a mean molar mass of M = 28.9 g/mol, determine the Reynolds number andMach number in flight. Justify your choice of characteristic length by referencinga commercial aircraft currently in service.(d) Is this flow inviscid or viscous? Is this flow subsonic or supersonic? Qualitativelydescribe the differences between these flight regimes.
Calculate the heat transfer from a 60 cm x 60 cm plate on which air flows at 40⁰C and. The plate temperature is 100⁰ C while the air speed is 5 m/s.Find the thickness of the boundary layer at a distance of x = 20 cm, for the same data in problem "number 1 In the picture below"
Air flows over a stationary flat plate at speed of 4,6 m/s . Plate has a width of 1 m. Air has a density of 1.2 kg/m3 and kinematic viscosity of 1.5x 10-5 m 2/s . Consider plate is totally in air flow field and upper and lower surfaces are identical a) Calculate maximum length of the plate to have a fully laminar flow (in m) b) Calculate total frictional force on the plate considering two surfaces (in N) c) In order to eliminate the frictional force on its surfaces calculate the plate speed(in m/s)
Water (ρ=1000 kg/m3) flows through a pipeline with inlet diameter 10 cm and outlet diameter 5 cm. The inlet and outlet gauge pressures measured to be 400 kPa and 130 kPa respectively. Assuming the pipeline to be horizontal and neglecting friction, calculate the outlet velocity(V2) of water by using continuity and Bernoulli’s equation.
Calculate thickness of the boundary layer (in metre) under laminar flow condition when distance from the upstream edge is 2.15 metre and local Reynolds number is 3000. Write the final answer in the box below.
A large plate is pulled at a constant speed of U = 4 m/s over a fixed plate on 5-mm-thick engine oil film at 20°C. Assuming a half-parabolic velocity profile in the oil film, as sketched, determine the shear stress developed on the upper plate and its direction. What would happen if a linear velocity profile were assumed?
A fluid with a constant density of 961 kg/m3 and a constant viscosity of 1.419×10-3 Kg/m.s is flowing over a flat plate at a stream free velocity of 0.87 m/s. If the plate has a length of 2 m, answer the following: 1.What is Reynolds number at a point that is (1/4)L down the entrance? 2.Is the flow laminar or turbulent? 3.Calculate the thickness of the boundary layer in mm at (1/4)L down the entrance 4.Calculate the drag coefficient at (1/4)L down the entrance