Exercise 2: Buck Converter Design: Design a buck converter to produce an output voltage of Vo=18 V across a R=10N load resistor. The output voltage ripple must not exceed 0.5 percent (AVo/Vo). The de supply is Vin=48 V. Design for continuous inductor current. Specify the duty ratio, the switching frequency, the values of the inductor L and capacitor C, the peak voltage rating of each device, and the ms current in the inductor and capacitor. Assume ideal components.

Exercise 2: Buck Converter Design: Design a buck converter to produce an output voltage of Vo=18 V across a R=10N load resistor. The output voltage ripple must not exceed 0.5 percent (AVo/Vo). The de supply is Vin=48 V. Design for continuous inductor current. Specify the duty ratio, the switching frequency, the values of the inductor L and capacitor C, the peak voltage rating of each device, and the ms current in the inductor and capacitor. Assume ideal components.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a)A 3-phase full converter delivers power to a load R=50 ohms. the source voltage is 400V,50Hz.For a firing-angle delay of 45 degrees, find the power delivered to the load R.(b)A single phase fully-controlled bridge converter supplies a load drawing constant ripple free current. if the firing angle is 30degrees.find the input power factor.
1.Design a buck converter and a resistive load operating in CCM mode with the following specifications:(∆V0)/V0= 0.5 %, Vin = 20 V, f =30 kHz, Duty cycle d=0.4, and R =5.33 Ω. Determine (a) the output voltage and current of the buck converter, the Critical(minimum) inductance for CCM mode (b) select L = 600 µH, find the maximum IL,max and the minimum IL,min inductorcurrents. find the capacitor value that corresponds to (∆V0)/V0= 0.5 % for this buck converter
45) We have buck converter, the maximum current of the inductor is Imax, the minimum inductor currentIs Imin. We now know the period of the switching signal is T=20 µs, the duty cycle D is 0.5, the load resistance R is 2 ohms, the input voltage is 30V, and the inductance L is 100 µH; What is Imax andIs Imin?
Power Electronics. In the Buck-Boost DC-DC converter circuit:Welding voltage [40-80]VSwitching frequency (f) 25khzVoltage between load terminals 55VCapacitance value 470uFLoad current value [10-25]A Under these conditions, which is the lowest ripple (delta IL) amount of the current passing through the coil (L) in Amps for the lowest L inductance value that can keep the DC-DC converter in a continuous current state? A) 23.9803B) 118.75C) 84.3750D) 47.5E) 59.9507F) 33.75
Please solve this 2 problems in detail Problem 1: Consider a step up converter with a resistive load of value R=10 Ohms. It is supplied by a DC power source of magnitude Vs=220 V. The switching frequency is 4 kHz and the duty cycle k is first set to 0.5 and the inductance used within the circuit has a value of L=20 mH. The switch is supposed to be ideal. Using the boundary conditions, the minimum and maximum load current values are equal to: Select one : a. 41.65A and 44.695A b. 43.32A and 44.695A c. None of these d. 43.32A and 47.85A Problem 2: A step up DC converter is used to control power flow from a DC votage Vs = 100V to a battery voltage E = 200V. The power transferred to the battery is 20 kw. The current ripple of the inductor is negligible. The duty cycle and the effective load resistance as seen from the input are respectively equal to: Select one: a. None of these b. 0.5, 0.5 Ohms c. 0.33, 0.5 Ohms d. 0.5, 0.33 Ohms
The buck converter with resistive load has the input voltage of 30[V], the output voltage of 20 [V] (constant), and the switching frequency of 30 [kHz]. If the output average power is 20[W], then determine the size of the inductor such that the minimum inductor current is 25 % of the average inductor current.
In the Buck - Boost DA-DA converter circuit, given below; 1) Source voltage (E) value: in the voltage range of [AB] (Volts) 2) Switching frequency (f) value: M kHz 3) Voltage between load terminals (Vload) F (Volt) 4) Capacitance value 470 (UF) 5) Load current lload) value: [KS] (Amps) current range The lowest Linductance value that can keep the DC-DC converter in continuous current condition under The lowest ripple (AIL) amount of the current passing through the coil (L) is given below in Amps. Which option do you see? A = 40 Volts B = 80 Volts M = 25kHz F = 55 Volts K = 10 Amps S = 25 Amps
A single phase full converter feeding RLE load has 230 V, 50 Hz source, R=2.5 ohm, E=100 v, firing angle=30° If the load inductance is large enough to make the load current virtually constant Find average of output voltage, output current and power factor.
100 V battery voltage to 75 V need a da-da circuit to reduce the voltage is heard. Transducer inductance 800 μH and loadresistance is given as 25 Ω. Power switch transmission duration is 20 μs, the circuit is in continuous conduction works. According to this; a) a) By specifying the name of the da-da converter used, draw b) Gate sign (vgs), switch voltage (vds), diode voltage Plot (vD), and inductance current (iL) c) Find the switching frequency and the transmission time of the diode.
Problem 2: Principles of analysis of converters in steady state.A steady state DC-DC Cuk converter is provided to you. The converter has a 24 V input, a desired 12 V output, and is operating at a switching frequency of 200 kHz. Design the circuit and calculate the required values for the inductors and capacitors. Analyze the behavior of the converter during the on and off periods.
I need help with question 1 (e). 1. Design a buck converter and a resistive load operating in CCM mode with the following specifications:(∆V0)/V0= 0.5 %, Vin = 20 V, f =30 kHz, Duty cycle d=0.4, and R =5.33 Ω. Determine(a) the output voltage and current of the buck converter.(b) the Critical(minimum) inductance for CCM mode(c) select L = 600 µH and find the maximum IL,max and the minimum IL,min inductorcurrents.(d) find the capacitor value that corresponds to (∆V0)/V0= 0.5 % for this buck converter(e) redesign the circuit above to achieve an output ripple voltage of 1 % and an inductor current ripple 10 % at the average load current with the same Duty cycle d, frequency, load Resistance,and Vin. Calculate the accepted new L and C.
2. Consider buck-boost converter with the following parameters: Vin=40 V, V0 =60 V, R=20 Ω, andL=750 µH. Determine the duty cycle? is this converter operates as a buck or a boost converter ?and Calculate IL,min and IL,max.