The buck converter with resistive load has the input voltage of 30[V], the output voltage of 20 [V] (constant), and the switching frequency of 30 [kHz]. If the output average power is 20[W], then determine the size of the inductor such that the minimum inductor current is 25 % of the average inductor current.

The buck converter with resistive load has the input voltage of 30[V], the output voltage of 20 [V] (constant), and the switching frequency of 30 [kHz]. If the output average power is 20[W], then determine the size of the inductor such that the minimum inductor current is 25 % of the average inductor current.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 2PP: Assume that the voltage drop across the resistor, ER, is 78 V; the voltage drop across the...

See similar textbooks

Similar questions

Inductive Circuits Fill in all the missing values. Refer to the following formulas: XL=2fLL=XL2ff=XL2L Inductance (H) Frequency (Hz) Inductive Reactance ( ) 1.2 60 0.085 213.628 1000 4712.389 0.65 600 3.6 678.584 25 411.459 0.5 60 0.85 6408.849 20 201.062 0.45 400 4.8 2412.743 1000 40.841
With reference to the attached circuit image: If the capacitor is now removed from the attached circuit and is placed in parallel with the secondary of the transformer. A) What is the impedance seen at the supply (HV side) B) What is the power dissipated by the tube
Draw the average model of the boost converter, clearly label the voltage port voltage, voltage port current, current port voltage, and current port current, as well as the transformer, turns ratio interms of duty cycle d(t)
The boost converter has the following parameters:Vd= 20V, D = 0.6, R = 12.5, L = 65 μH, C = 200 μF, fs= 40 kHz.Determine(a) output voltage, (b) average, maximum and minimum inductor current, (c) outputvoltage ripple.
A transformer-coupled class A amplifier drives a 16 Ω speaker through a 3.87:1 transformer. Using a powersupply of VCC = 36 V, the circuit delivers 2 W to the load. Calculate:a. P(ac) across transformer primary.b. VL(ac).c. V(ac) at transformer primary.d. The rms values of load and primary current.
a. A single-phase semi-converter supplies an inductive load having an impedance of 3k. Assume that the output current is constant and is equal to Id. If the supply voltage is 220V and the firing angle is maintained at /2, calculate (i) Average output voltage, (ii) Supply RMS current, (iii) Supply fundamental RMS current.
Design a buck converter such that the output voltage varies between from 20V to 28V while the input voltage is 40V. The maximum load power is 200Wde. Assume the switching frequency is 15kHz. (a) Design the converter such that it will be in continuous current mode. (b) The capacitor realized output voltage ripple must not be more than 1% at worst case. (c) The inductance realizes CCM at worst case. (d) Select the appropriate switch and other elements
Consider a transformer with a primary coil consisting of 1226 turns and a secondary coil of 1078 turns. An alternating RMS voltage 211 V is applied to the primary coil, and the output RMS voltage 39.5 V is measured across the load resistor of resistance 133.5 Ohm connected to the secondary coil. What is the internal resistance of the secondary coil?
just need fınal answer Since Vi = 20 mV, Vcc = 25 V, RB = 470 kΩ, RC = 3.2 kΩ, RE1 = 470 Ω, RE2 = 1.2 kΩ, RL = 42 kΩ and β = 110 in the circuit in the figure, the value of the output voltage (Vo) find it. NOTE-1: Capacitors are negligible at mid-band frequency. NOTE-2: The output impedance of the transistor (r0) will be neglected. a. -197,96 mV b. -222,71 mV c. -98,98 mV d. -148,47 mV e. -123,73 mV f. -173,22 mV g. -247,45 mV h. -74,24 mV
Get the following parameters: RC RE RB VCE VB
A boost converter has the following parameters: output of 30 V from a 12-V source, R = 40 Ω. for continuous inductor current and an output ripple voltage of less than one percent. then the minimum inductance for continuous current is 100 µH. Select one: True False
For the circuit in figure 1, the current source is represented byi1 (t) = 6 + 8 cos (377t) + 10 cos (754t) Amps For this problem, determine: The average power of the source current Pave The source current distortion factor (DF) and thesource current Total Harmonic Distortion (THD)