Exercise 2.20 ▸ A circuit consists of two impedances, ▸ Z₁ = 20 30º Q and Z₂ = 25 2-60° 0 in parallel, supplied by a source voltage V = 100 Z 60 volts. ▸ Determine and draw the power triangle for each of the impedances and for the source. ▸ S₁ =(433+j250)VA ▸ S₂ =(200-j346.4)VA ▸ST = (633-j96.4)VA

Exercise 2.20 ▸ A circuit consists of two impedances, ▸ Z₁ = 20 30º Q and Z₂ = 25 2-60° 0 in parallel, supplied by a source voltage V = 100 Z 60 volts. ▸ Determine and draw the power triangle for each of the impedances and for the source. ▸ S₁ =(433+j250)VA ▸ S₂ =(200-j346.4)VA ▸ST = (633-j96.4)VA

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.17MCQ: Consider the load convention that is used for the RLC elements shown in Figure 2.2 of the text. A....

See similar textbooks

Similar questions

InclassofENG100youwereaskedtoconnectacoilofresistance50Ωand inductance0.318Hwithacircuitcomprisinga75Ωresistorinserieswitha 159µFcapacitor.Andyouconnectedyourresultingcircuittoa240v,50HzAC supply. Calculate: (a)the supply current of your circuit; EV(7) (b)the circuit impedance, resistance and reactance; CR(7) (c)the phase angle of the resulting current,use (sine) as your reference and explain your result. AN(6) Question2
A coil of wire having a value of (5 + j8) ohms is connected in series with acapacitive reactance Xc, and this series combination is then connected in parallel with a resistor R. If the equivalent impedance of the circuit is 4 /0 o ohms, calculate the values of Xc and R.
α=4 β=4For the adjacent circuit, Vab=(400+5β)V is given and the source part is balanced. Since it is known as ZAN=j2α Ω, ZBN= 3α Ω and ZCN=-j3α Ω, calculate the value of the current Ib by its angle, ignoring the impedances of the transmission lines.Can you please post your solutions, it's very important
A coil of wire having a value of (5 + j8) ohms is connected in series with a capacitive reactance Xc, and this series combination is then connected in parallel with a resistor R. If the equivalent impedance of the circuit is 4 /0o ohms, calculate the values of Xc and R.
Given the voltage υ(t) = 120 cos (314t + π/4) V, determine the frequency ofthe voltage in Hertz and the phase angle in degrees. 2- Three branch currents in a network are known to bei1(t) = 2 sin (377t + 45°) Ai2(t) = 0.5 cos (377t + 10°) Ai3(t) = - 0.25 sin (377t + 60°) A Determine the phase angles by whicha) i1(t) leads i2(t)b) i1(t) leads i3(t).
Consider the load convention that is used for the RLC elements shown in Figure 2.2 of the text. A. If one says that an inductor absorbs zero real power and positive reactive power. is it (a) True (b) False B. If one says that a capacitor absorbs zero real power and negative reactive power (or delivers positive reactive power), is it (a) False (b) True C. If one says that a (positive-valued) resistor absorbs (positive) real power and zero reactive power, is it (a) True (b) False
Solve the impedances of the circuit using mesh analysis. Complete the table given. Note: If there are no coefficients for a particular parameter, input zero. Round off only the final answer to five decimal places if possible. @mesh 1: Z11I1 + Z12I2 +Z13I3 + Z14I4 = Source1 @mesh 2: Z21I1 + Z22I2 + Z23I3 + Z24I4 = Source2 @mesh 3: Z31I1 + Z32I2 + Z33I3 + Z34I4 = Source3 @mesh 4: Z41I1 + Z42I2 + Z43I3 + Z44I4 = Source4
Given the voltage υ(t) = 120 cos (314t + π/4) V, determine the frequency of the voltage in Hertz and the phase angle in degrees. (Answer: 50 Hz ; 45°) 2- Three branch currents in a network are known to be i1(t) = 2 sin (377t + 45°) A i2(t) = 0.5 cos (377t + 10°) A i3(t) = - 0.25 sin (377t + 60°) A Determine the phase angles by which a) i1(t) leads i2(t) b) i1(t) leads i3(t).
Please solve A line with impedance of 1 +j 0.32 Q is used to deliver power to a load. The load is inductive and the load voltage is 220 0° Vrms at 50Hz. If the load operates at 40 kw with a power factor of 0.75 lagging, determine the complex power in both the load and the line current. 9.2) draw the phasor diagram for the circuit, 9.3) calculate the power savings if power factor is changed to .95.
2) An industrial plant is supplied from 400V 50Hz power system. The plant consists of(i) 2x50kW pure resistive heating furnace(ii) 5x25kW induction motor having a lagging power factor of 0.85(iii) A compressor unit drawing 80kW active power and 60kVAr inductive reactive power.Calculate per phase capacitance of delta (∆) connected reactive power compensation system to setthe power factor of the industrial power plant to 0.98 leading.
1 A circuit having a resistance of 12Ω, an inductance of 0.15 H and a capacitance of 100μf in series is connectedacross a 100V, 50Hz supply. Calculate the impedance, current, the phase difference between the current andsupply voltage. 2. Two circuits with impedances of Z1 = 10 + j15Ω and Z2 = 6 – j8Ω are connected in parallel. If the supply current is 20A, what is the power dissipated in each branch?
S1) The serial impedance per unit length of a three-phase 140 km power transmission line is 0.09 + j0.88 ohm/ km and its admittance is j4.1x10-6 S / km. Power factor under 210 kV interphase voltage from the end of this energy transmission line A power of 150 MVA, which is 0.85 back, is drawn. Using this transmission line data and the T equivalent circuit model, the line Calculate the head voltage (V1), current (I1) and load angle.