Exercise #4: A flexible shaft consists of a 0.20-in-diameter steel wire encased in a stationary tube that fits closely enough to impose a frictional torque of 0.50 lb-in/in. Determine the maximum length of the shaft if the shearing stress is not to exceed 20 ksi. What will be the angular deformation of one end relative to the other end? G = 12 x 106 psi.

Exercise #4: A flexible shaft consists of a 0.20-in-diameter steel wire encased in a stationary tube that fits closely enough to impose a frictional torque of 0.50 lb-in/in. Determine the maximum length of the shaft if the shearing stress is not to exceed 20 ksi. What will be the angular deformation of one end relative to the other end? G = 12 x 106 psi.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cantilever beam carries a trapezoidaldistributed load (see figure). Let wB = 2.5 kN/m,wA = 5.0 kN/m, and L = 2.5 m. The beam has amodulus E = 45GPa and a rectangular cross sectionwith width b = 200 mm and depth h = 300 mm.Use the method of superposition and Cases 1 and8 in Table H-1 to calculate the def lection and rotationat B.
4. An aerial copper wire (E =1x 10 5 N/mm ^2) 40 m long has cross sectional area of80 mm2 and weighs 0.6 N per meter run. If the wire is suspended vertically, calculatethe maximum weight which this wire can support at its lower end if the limiting valueof stress is 65 N/mm 2.a. 4627 Nb. 4281 NC. 4519 Nd. 5188 N
QUESTION-1: Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and CAssume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15If there is a settlement of S at the support C, solve the following using slope deflection method:
Compute the value of EIy at 2.5 m from the left support.
Determine the vertical displacement of joint A if members AB and BC experience a temperature increase of ΔT = 200°F. Take A = 2 in2 and E = 29(103) ksi. Also, α = 6.60 (10-6) /°F.
Solve the problem completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Design the number of 36 mm diameter bars to support the maximum positive moment of Mu=1600 kN.m. Use f'c=28MPa, fy=345MPa, h=800mm, bf=1000mm, bw=400mm, flange thickness=100mm, stirrups=10mm, and cc=40mm. Calculate the effective depth of the final section in mm.0 Calculate the depth of the compression block of the final section in mm.0 Calculate the depth of the neutral axis of the final section in mm.0 Calculate the ultimate moment capacity of the final section in kN.m.0
The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque T (in Nm) that can be applied to the ends of the shaft without exceeding a shear stress of 70048581 Pa and angle of twist of 2.29ᴼ. Use G = 83000000000 Pafor the shaft, x = 2.01 m, and y = 1.69 m. Round off the final answer to two decimal places.
THE ANSWER MUST BE IN FOUR DECIMAL PLACES the steef shaft shown in figure rotates at 4Hz with 35 KW taken off at A, 20 kW removed at B and 55 kW applied at C. Using G=83 GPa, find the maximum shearing stress and the angle of rotation of gear A relative to gear C
: Block B has a mass m and is released from rest when it is on top of cart A, which has a mass of 3kg. Determine the tension in cord CD needed to hold the cart from moving while B slides down A. Neglect friction. =30o
The moment diagram (answer in kips) P=8.3 kips, b = 23 ft, h=13 ft
Determine the bending moment 2.16 m to the right of point A for the beam shown belowif P = 1990 N, T = 4712 Nm, a = 0.99 m, b = 0.7 m, and c = 1.29 m. Round of the final answer (in N m) to four decimal places.