For each of the loadings shown below, write the load using singularity functions and give the boundary conditions that must be met for the deformation. You can either use the symbols or the numbers if both are given. a. Overhang 3200 Ib 300 Ib/ft A C D. 4ft 4 ft 4 ft b. Cantilever 4.5 kN B 2.4 m 1.8 m 3 kN w =1.5 kips/ft, L=4 ft, d= 2 ft с. A. L/2 L.

For each of the loadings shown below, write the load using singularity functions and give the boundary conditions that must be met for the deformation. You can either use the symbols or the numbers if both are given. a. Overhang 3200 Ib 300 Ib/ft A C D. 4ft 4 ft 4 ft b. Cantilever 4.5 kN B 2.4 m 1.8 m 3 kN w =1.5 kips/ft, L=4 ft, d= 2 ft с. A. L/2 L.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the beam shown in (Figure 1). Suppose that M = 9 kip⋅ft, P = 6 kip, w = 1.2 kip/ft, and point D is located just to the left of the 6-kip load. Follow the sign convention. Part A Part complete Determine the internal normal force at section passing through point D. Express your answer to three significant figures and include the appropriate units. Part B Determine the internal shear force at section passing through point D. Express your answer to three significant figures and include the appropriate units. Part C Determine the internal moment at section passing through point D. Express your answer to three significant figures and include the appropriate units. Part D Part complete Determine the internal normal force at section passing through point E. Express your answer to three significant figures and include the appropriate units. Part E Determine the internal shear force at section passing through point E. Express your answer to…
Consider the beam shown in (Figure 1). Suppose that M= 9 kip⋅ft, P= 6 kip, w = 1.2 kip/ft, and point D is located just to the left of the 6-kip load. Follow the sign convention. Part D Part complete Determine the internal normal force at section passing through point E. Express your answer to three significant figures and include the appropriate units. Part E Determine the internal shear force at section passing through point E. Express your answer to three significant figures and include the appropriate units. Part F Determine the internal moment at section passing through point E. Express your answer to three significant figures and include the appropriate units.
Calculate the vertical shear stress (N / cm2) at point A in the critical section of the beam below whose load and section is given? The cross section is symmetrical with respect to the y-axis. (Point A is on the body, point B is on the x-axis and point C is on the header.) (Q = 6000 N / m, P = 60000 N, L = 3 m, b = 50 cm t = 5 cm, h = 20 cm) please fast help please
A steel plate 2.5 m x 1.6 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the shear stress (MPa) in the 16 mm diameter pins through the clevis The correct answer is 45.33. Show solution.
For the beam shown in the figure, the allowable bearing stress for the material under the supports at A and B is σb = 900 psi. Assume that w = 2,000 lb/ft, P = 4,500 lb, a = 20 ft, and b = 8 ft. Determine the size of square bearing plates (A and B) required to support the loading shown.
The following rigid structure ABCD is supported by a hinge at B and two bars at C and D. The applied load is 100 kN. The data is shown in the table. Determine: The stress in each bar. Answ: 27.01 MPa, 328.01 MPa The vertical displacement at the point where the load is applied. Answ: 0.9403 mm. The rotation at point B. Answ: 0.001069 rad. The horizontal displacement 400 mm below point B. Answ: 0.42741 mm.
A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 2 m on centers, on simple supports over a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c = 21 MPa, long bar fy = 415 MPa, calculate: Using a T-beam geometry, determine the required amount of flexure bars for maximum ultimate bending. = [As] sq.mm (whole number)
Loads are applied with rigid bearing plates to a system of steel bars, as shown in the figure. The cross-sectional areas are 18in2for bar AB, 5in2 for bar BC, and 14in2for bar CD. Determine the normal stress on a typical cross section in each of the bars.
Completely solve and box the final answer. Write legibly 1. A built up wooden beam is made up of two 50 mm by 150 mm sections glued on the lower sides of a 100 mm by 250 mm section. Calculate the maximum bending stress if the 6 m simple beam is loaded with 2.8 kN/m.
A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform load of 10 KN/m all through out its length and a concentrated load of 500 N at the midspan. The cross-sectional area of the beam is indicated below. What is the actual bending stress of the beam in MPa? (use two decimal places, no need for unit) What is the actual shearing stress of the beam in MPa? (use two decimal places, no need for unit)
A load P is supported by two steel springs arranged in series as shown. The upper spring has 20 turns of 20mm diameter wire on a mean diameter of 150 mm. The lower spring consists of 15 turns of 10 mm diameter wire on a mean diameter of 130 mm. Determine the maximum shearing stress in each spring if the total deflection is 80 mm and G = 83 Gpa. Use exact method.
The end chord of a timber truss is framed into the bottom chord as shown in the figure. Neglecting friction, compute dimension b (in mm) if the allowable shearing stress is 880,000 Pa. (round-up your answer to a nearest whole number that is divisible by 5, no need for unit)