Exercise 4.6.3 A solid cylinder of 10 cm diameter generates 0.3 G W/m' of heat due to nuclear reaction. If the outside temperature is 40°C and the heat transfer coefficient from the solid surface to the surrounding fluid is 30 W/m2 C, calculate the temperature distribution using quadratic elements. Assume a thermal conductivity of 15 W/m C.

Exercise 4.6.3 A solid cylinder of 10 cm diameter generates 0.3 G W/m' of heat due to nuclear reaction. If the outside temperature is 40°C and the heat transfer coefficient from the solid surface to the surrounding fluid is 30 W/m2 C, calculate the temperature distribution using quadratic elements. Assume a thermal conductivity of 15 W/m C.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.2P: 2.2 A small dam, which is idealized by a large slab 1.2 m thick, is to be completely poured in a...

See similar textbooks

Similar questions

A plane wall, 7.5 cm thick, generates heat internally at the rate of 105 W/m3. One side of the wall is insulated, and the other side is exposed to an environment at 90C. The convection heat transfer coefficient between the wall and the environment is 500 W/m2 K. If the thermal conductivity of the wall is 12 W/m K, calculate the maximum temperature in the wall.
A plane wall 15 cm thick has a thermal conductivity given by the relation k=2.0+0.0005T[W/mK] where T is in kelvin. If one surface of this wall is maintained at 150C and the other at 50C, determine the rate of heat transfer per square meter. Sketch the temperature distribution through the wall.
2.2 A small dam, which is idealized by a large slab 1.2 m thick, is to be completely poured in a short Period of time. The hydration of the concrete results in the equivalent of a distributed source of constant strength of 100 W/m3. If both dam surfaces are at 16°C, determine the maximum temperature to which the concrete will be subjected, assuming steady-state conditions. The thermal conductivity of the wet concrete can be taken as 0.84 W/m K.
In steady state condition, the lateral surfaces of the plate are insulated, and the bottom surface is heated with a uniform heat flux. The thermal conductivity coefficient of the plate is k, and its upper surface is cooled by convection. a) Find the temperature distribution inside the plate. b) Find the temperatures at x = 0 and x = L. c) Find the amount of heat transfer transferred. NOTE: Assume one-dimensional heat conduction. h = 27 W/m2°C q" =624000W/m² k=15 W/m.°C T = 22°C L=256 cm
4) In an experiment to find the thermal conductivity, a metallic rod of diameter 25 mm is placed in a furnace such that its one half is inserted into the furnace and other half is projected out in a room at 300 K. Once the steady state reached, the temperatures measured between two points 76 mm apart were 399 K and 364 K, respectively. Taking a convection coefficient of 22.7 W/m 2 – K, find the thermal conductivity of the metal.
Water vapor at a temperature of 120 ° C flows through a stainless steel pipe (k = 57 W / mK). The inner diameter of the pipe is 47 mm, the outer diameter is 50 mm, and the length is 100 m. The heat transfer coefficient between the water vapor and the pipe wall is 200 W / m²K, and the heat transfer coefficient between the outer surface of the pipe and the ambient air is 25 W / m_K. The outdoor air temperature is 10 ° C. Find the thermal conductivity coefficient of the insulation material, since it is desired to insulate with an insulation material with a layer thickness of 50 mm in order to reduce the loss of heat from the pipe by 60%.
Two volumes of air are separated by a thin rectangular heater (0.2 cm x 15 cm x 2 cm). The volumetric heat generation associated with the heater is 350 kW/m3. What is the temperature of the heater at steady state?The air in the bottom chamber is at (TB= 20 °C, hB= 15 W/m2.K) while the air in the top chamber is at (TT= 55 °C, hT= 9 W/m2K). hint: for such thin application, we shall assume the same surface temperature on both sides of the heater.
a.) Determine the thermal conductivity of the plasterboard (kp), in W/m*K b) Determine the value of the inside convection resistance (Ri), in degrees C/W. c) Determine the value of the fiberglass blanket resistance (Rb), in degrees C/W. d) Determine the value of total heat transfer resistance (Rtotal), in degrees C/W. e) Determine the value of heat loss (q), in kW.
Steam at 150 ° C flows in a pipe having an inner radius of 50 mm and an outer radius of 55 mm. The convective heat transfer coefficient between the steam and the inner pipe wall is 2500 W / (m² ° C). The outer surface of the pipe exposed to ambient air is 25 ° C with a convective heat transfer coefficient of 10 W / (m² ° C). Assuming steady state, calculate the rate of heat transfer per meter of pipe from steam to air. Assume that the thermal conductivity of stainless steel is 15 W / (m ° C.). Steps of work according to example 4.16 Singh. a. Find the overall heat transfer coefficient = Answer W / m² ° C. b. Heat transfer rate per meter of pipe = Answer
Steam at 140 ° C flows in a pipe having an inner radius of 50 mm and an outer radius of 55 mm. The convective heat transfer coefficient between the steam and the inner pipe wall is 2500 W / (m² ° C). The outer surface of the pipe exposed to ambient air is 20 ° C with a convective heat transfer coefficient of 10 W / (m² ° C). Assuming steady state, calculate the rate of heat transfer per meter of pipe from steam to air. Assume that the thermal conductivity of stainless steel is 15 W / (m ° C.). Steps of work according to example 4.16 Singh. a. Find the overall heat transfer coefficient = Answer W / m² ° C. b. Heat transfer rate per meter of pipe = Answer W / m.
The 1 ft thick walls of a building are made of concrete (k = 2 Btu/h·ft·F). The outside temperature and heat transfer coefficient are 50 F and 2 Btu/h·ft2·F, respectively. Find the rate of heat transfer through 1000 ft2 of the wall if the inside temperature and heat transfer coefficient are 120 F and 1 Btu/h·ft2 F, respectively. Both the inside and the outside of the wall are coated with 20 mils of paint (k = 0.1Btu/h·ft·F) where 1 mil = 1E-3 in. Compare the results with a bare wall.
Consider a single cylindrical fin of a uniform cross-sectional area (D = 5 mm, L = 70 mm, k = 400 W/m.K) that is attached to a wall with a base temperature of Tb = 180 C. Ambient conditions are T∞ = 50 °C and h = 210 W/m2.K.a. What is the heat transfer rate of a single fin?b. Plot the temperature distribution within the fin (Excel, MATLAB, … etc.)c. What is the material of the fin?